Search found 1562 matches
- Fri Feb 10, 2012 6:45 pm
- Forum: Performance Technical
- Topic: Sym dd w/ hona dio engine i need help please!
- Replies: 145
- Views: 60462
Re: Sym dd w/ hona dio engine i need help please!
Jacob, the Jiangwayne V-8 pipe is good with the corsa kit, my neighbor has the same set up, they will also ship to UK no problem from taiwan. Some of those V-8 pipes are different but the first one you posted back there is the real deal. Good Luck.
- Wed Feb 08, 2012 3:41 pm
- Forum: Scooter Showcase
- Topic: 89 Elite R - my first build
- Replies: 288
- Views: 82789
Re: 89 Elite R - my first build
Maybe not adjust that much at once, quarter turns and wait five seconds to hear the motor. If idle drops too much, go back one eighth in and listen before adjusting again. Get the air-to-fuel set, then adjust at the idle. If you are more than two turns out on a/f then you lower the pilot jet. Glad y...
- Wed Feb 08, 2012 3:31 pm
- Forum: Technical Help
- Topic: Carb Nipple
- Replies: 20
- Views: 6728
Re: Carb Nipple
Cheap - as in less expensive than a brand new carburetor from Honda dealer.
I guess I should have said that instead. Probably somewhere between $30 - $50. Depends on condition.
I like the solutions given so far. No cost to try.
I guess I should have said that instead. Probably somewhere between $30 - $50. Depends on condition.
I like the solutions given so far. No cost to try.
- Wed Feb 08, 2012 8:25 am
- Forum: Technical Help
- Topic: Carb Nipple
- Replies: 20
- Views: 6728
Re: Carb Nipple
Maybe just try another carb. and be on your way. Plenty of pre owned units around here for cheap. Sometimes this is the best solution.
What kind of scooter is it going on? Stock or mod?
What kind of scooter is it going on? Stock or mod?
- Mon Feb 06, 2012 2:03 pm
- Forum: Scooter Showcase
- Topic: 89 Elite R - my first build
- Replies: 288
- Views: 82789
Re: 89 Elite R - my first build
Forgive me, I've been looking at stock carbs threads. Sorry about the weather. There should be a needle in that slide. When you pull that plastic retainer out, there is also a chrome metal slide down in the body of the carb. Stick your finger in there and pull it out. It should have a brass needle i...
- Mon Feb 06, 2012 1:47 pm
- Forum: Scooter Showcase
- Topic: 89 Elite R - my first build
- Replies: 288
- Views: 82789
Re: 89 Elite R - my first build
Not to adjust the needle clip position. Here is the proceedure as I know it. Unskrew the cap at the throttle cable, and you will be able to pull the slide straight out so as not to bend the needle. The side of the slide has a notch in it which is so you can remove the cable. Holding the cap, push th...
- Mon Feb 06, 2012 1:36 am
- Forum: General Discussion
- Topic: homemade sidestand
- Replies: 15
- Views: 7869
Re: homemade sidestand
That's awesome baka, thanks for the blueprint, and your simplicity in design.
I think I'll give it a try!
I think I'll give it a try!
- Mon Feb 06, 2012 12:11 am
- Forum: Performance Technical
- Topic: Sym dd w/ hona dio engine i need help please!
- Replies: 145
- Views: 60462
Re: Sym dd w/ hona dio engine i need help please!
Perhaps a set could be found in the pacific islands or a search on forums hawaii. Be careful. Is your cdi rpm limited? You said you were going 65 mph? That doesn't sound limited to me. Just say'in. You might have meant 65 kph? Anyway, there are cdi's that aren't limited, in fact, I have one that I p...
- Sun Feb 05, 2012 12:50 pm
- Forum: Technical Help
- Topic: play in rear wheel
- Replies: 3
- Views: 1066
Re: play in rear wheel
Hey Joe, if you run out of solutions you can also check the bearings on the final shaft. The shaft that holds the wheel on and goes into the transmission. Check both the inner, and the outer bearings for play and visually, sometimes they spin in the case if they have overheated.That is my experience...
- Fri Feb 03, 2012 9:33 pm
- Forum: Performance Technical
- Topic: Where can i find polini or malossi exhaust pipe?
- Replies: 25
- Views: 10156
Re: Where can i find polini or malossi exhaust pipe?
Scottinscotty, I wasn't gunna do this on your thread but this keeps coming to mind:
http://www.treatland.tv/honda-dio-simon ... -black.htm
Best of luck.
http://www.treatland.tv/honda-dio-simon ... -black.htm
Best of luck.
- Fri Feb 03, 2012 11:58 am
- Forum: General Discussion
- Topic: anyone know the forum user, lonomack?
- Replies: 9
- Views: 2452
Re: anyone know the forum user, lonomack?
Are you saying the delivery service beat it up, or the person who shipped it?iceman77 wrote:pipe came in today. it's pretty beat up but it's here.
TJ
Glad you finally got it and hope you get some good out of it.
- Thu Feb 02, 2012 11:58 pm
- Forum: Performance Technical
- Topic: Boost port
- Replies: 11
- Views: 3944
Re: Boost port
Nice work, King! I did mine and then polished everything, then I learned that I shouldn't have polished anything. I sanded it all back to a dull surface again with 150 grit.
It's tuff work and my big hands hated it! Good luck with the build.
It's tuff work and my big hands hated it! Good luck with the build.
- Thu Feb 02, 2012 9:21 pm
- Forum: General Discussion
- Topic: how fast is this
- Replies: 7
- Views: 1888
Re: how fast is this
If the odometer was going backwards, about 55. :*:iceman77 wrote:My speedo needle was on the E for the empty on fuel. how fast was i going? assuming that it is correct.
Thanks:
TJ
What were the temps?
Swimming free? your dog has a gas gauge?
- Thu Feb 02, 2012 9:17 pm
- Forum: General Discussion
- Topic: anyone know the forum user, lonomack?
- Replies: 9
- Views: 2452
Re: anyone know the forum user, lonomack?
Me too, wouldn't surprise me if it was.
- Thu Feb 02, 2012 8:49 pm
- Forum: General Discussion
- Topic: anyone know the forum user, lonomack?
- Replies: 9
- Views: 2452
Re: anyone know the forum user, lonomack?
Yeah i know that guy he lives in the same town as me. Did you use paypal? I would get your money back yeah i sent the money through paypal...so is this guy not cool or what? do you think he'll send my pipe? TJ Well, did you ever get your pipe? If so , what's the story? I'm just dying to know how it...