Search found 149 matches

by otto-man
Fri Nov 11, 2022 10:34 pm
Forum: Technical Help
Topic: Running like crap
Replies: 9
Views: 2254

Re: Running like crap

Maybe the gas cap vent is plugged
by otto-man
Wed Oct 27, 2021 8:22 pm
Forum: Technical Help
Topic: honda metropolitan wiring
Replies: 1
Views: 988

Re: honda metropolitan wiring

After LOTS of research, the two mentioned wires plug together. It makes no sense, but apparently they do.
by otto-man
Sat Oct 23, 2021 3:09 pm
Forum: Technical Help
Topic: honda metropolitan wiring
Replies: 1
Views: 988

honda metropolitan wiring

Greetings scooterists! I recently aquired a 2008 Honda Metropolitan "basket case". I've got it 85% completed and when wiring the speedometer to the harness, I came across 2 wires coming out of the speedometer that have me stumped. About a 3" green/orange wire with a female bullet conn...
by otto-man
Wed May 19, 2021 3:01 pm
Forum: Technical Help
Topic: 2007 Honda Metropolitan runs really bad
Replies: 6
Views: 3539

Re: 2007 Honda Metropolitan runs really bad

Tried 2 other ignition coils.....no change. Checked thermostat sensor....no change.
by otto-man
Mon May 17, 2021 8:46 pm
Forum: Technical Help
Topic: 2007 Honda Metropolitan runs really bad
Replies: 6
Views: 3539

Re: 2007 Honda Metropolitan runs really bad

I'll check it out. Thanks
by otto-man
Sat May 15, 2021 11:14 am
Forum: Technical Help
Topic: 2007 Honda Metropolitan runs really bad
Replies: 6
Views: 3539

Re: 2007 Honda Metropolitan runs really bad

It doesn't seem like the cooling system is the problem. The radiator and hoses are warm after running for a few minutes and I get a few air bubbles when bleeding the system. Coolant light on speedometer doesn't come on (tested light and it works). After short ride at 25 mph, motor slows to idle and ...
by otto-man
Tue May 11, 2021 11:27 pm
Forum: Technical Help
Topic: 2007 Honda Metropolitan runs really bad
Replies: 6
Views: 3539

Re: 2007 Honda Metropolitan runs really bad

Tried known good stator, reset data.......no change.
by otto-man
Sun May 09, 2021 9:34 pm
Forum: Technical Help
Topic: Spree kickstand removal!!?!? Please help!!!
Replies: 2
Views: 2282

Re: Spree kickstand removal!!?!? Please help!!!

Ahhhh yes, the Spree kickstand removal and reinstall! Usually bloody knuckles and using words not suitable for kids is what happens. Here's what I do. If you have a stand, clamp the front wheel or have someone hold the scooter. With the stand up, remove the cotter key from the right side and slide t...
by otto-man
Sun May 09, 2021 8:31 pm
Forum: Technical Help
Topic: 2007 Honda Metropolitan runs really bad
Replies: 6
Views: 3539

2007 Honda Metropolitan runs really bad

Picked up a 2007 Honda Metropolitan with 6800 miles,(not a Metropolitan 2), that was stored for 6 years. Has new battery and obviously the carb had to be cleaned and new carb kit and float needle. Starts and idles like new. Everything works. Good throttle response but will not go over 25 mph.When wa...
by otto-man
Thu Feb 18, 2021 3:56 pm
Forum: Technical Help
Topic: Request for input - Parts Spree 84/85 vs 86/87 and SB50
Replies: 44
Views: 74026

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

While reviewing this site, I came upon the part about crankshaft bearings that anyone rebuilding a 1986/1987 Honda Spree should be aware of. The drive side bearing stated to be a generic 6204 (20x47x14) is too wide. I tried one a few years ago and the cases will NOT come together. The correct bearin...
by otto-man
Mon Jan 04, 2021 10:43 pm
Forum: Technical Help
Topic: 1984 Honda Spree wont start
Replies: 4
Views: 2776

Re: 1984 Honda Spree wont start

Could be a lot of things.... Is spark plug wet? Check crank seals (left side sometimes comes loose). Does it have compression? Is carb CLEAN? Is air filter in good condition(not crumbly)? Timing correct? It's winter in Minnesota and 2 strokes sometimes don't run in the cold weather. How warm is it w...
by otto-man
Sat Oct 24, 2020 11:14 pm
Forum: Technical Help
Topic: 1990 Elite LX 50 (SA50) grinding sound
Replies: 16
Views: 6465

Re: 1990 Elite LX 50 (SA50) grinding sound

Greetings: Vise Grips could conceivably damage the drive face. Pick up THIS. You can get it much cheaper if you shop. The pins lock the clutch too. Excellent tool for clutch, drive pulley, flywheel, etc. I've had one for years. One thing about buying tools...You usually forget how much you pay for ...
by otto-man
Thu Aug 27, 2020 12:00 am
Forum: Technical Help
Topic: 1990 Elite LX 50 (SA50) grinding sound
Replies: 16
Views: 6465

Re: 1990 Elite LX 50 (SA50) grinding sound

You shouldn't need locktite if you torque the nut down to 30 ft/lbs.
by otto-man
Mon Aug 10, 2020 10:12 pm
Forum: Technical Help
Topic: 1986 Honda Spree HELP
Replies: 6
Views: 3815

Re: 1986 Honda Spree HELP

Parts are on the way.....Good luck!
by otto-man
Sat Aug 08, 2020 10:48 pm
Forum: Technical Help
Topic: Where to find replacement steering bearings
Replies: 6
Views: 3893

Re: Where to find replacement steering bearings

I use Kenda 2.50x10 tires from J&PCycles. They're the cheapest I can find. Less than $20 each tax included and shipping is free if you order more than $39. They have a lot of good stuff! Those bearings can get lost pretty easy. If you lose any, I can send you some. 26 in the bottom race and 26 i...