Search found 22 matches
- Tue Apr 02, 2013 3:31 pm
- Forum: Technical Help
- Topic: 85 Spree bogs when about half throttle, bogs under load
- Replies: 10
- Views: 4756
Re: 85 Spree bogs when about half throttle, bogs under load
ok I got it figured out......the tall tube by the tube with the jet in it was clogged. used some throttle body cleaner to soak it in the tube, used compressed air and gunk flew out of it. got it all put back together and it still is a little funny riding but I think it is from the centrifugal clutch...
- Wed Feb 06, 2013 12:48 pm
- Forum: Technical Help
- Topic: 85 Spree bogs when about half throttle, bogs under load
- Replies: 10
- Views: 4756
Re: 85 Spree bogs when about half throttle, bogs under load
The air box does have the seal.....i ordered a new air filter just to be safe, i did remove the tube under the jet and cleaned it too (does it have to be put back in a certain way?) Not sure about the muffler if its original or not....how much do 68 jets run cost wise? and where do i get one?
- Mon Feb 04, 2013 9:47 am
- Forum: Technical Help
- Topic: 85 Spree bogs when about half throttle, bogs under load
- Replies: 10
- Views: 4756
Re: 85 Spree bogs when about half throttle, bogs under load
Main jet is a 65....... i talked to the guy that did my rings.....he honed the cylinder...and also he broke the bottom ring when he installed it the first time and installed another top ring in the bottom ring slot.....he said it wouldnt make any diference except a little more smoking during operati...
- Thu Jan 31, 2013 5:45 pm
- Forum: Technical Help
- Topic: honda spree dies at full throttle.
- Replies: 7
- Views: 3613
Re: honda spree dies at full throttle.
I realize this is an older thread, but i am having the same exact problem......did you find an answer for it?
- Thu Jan 31, 2013 2:40 pm
- Forum: Technical Help
- Topic: 85 Spree bogs when about half throttle, bogs under load
- Replies: 10
- Views: 4756
85 Spree bogs when about half throttle, bogs under load
Got an 85 sprre i did and engine swap on, iowa model engine swapped in with correct carb. New rings just installed. Get it all back together and the thing starts just fine and will idle, but giving it throttle and it will reach a certain point and just sound like its starving itself for gas or its f...
- Fri Oct 26, 2012 5:30 pm
- Forum: Technical Help
- Topic: 85 NQ50 problems starting...
- Replies: 16
- Views: 6846
Re: 85 NQ50 problems starting...
So which set of rings do i need, there are a few of them listed for sale......i know the ones are for over-bored, but theres a (NIPPON) set and a standard set......how do i know which one i need?
- Wed Oct 24, 2012 1:42 pm
- Forum: Technical Help
- Topic: 85 NQ50 problems starting...
- Replies: 16
- Views: 6846
Re: 85 NQ50 problems starting...
Well....i retested my compression with a different tester today and i have 80 for the reading, put a cab full of oil in the hole and retested at 110......looks like i need me some rings.....85 nq50, wheres a good place to get em cheap?
- Tue Oct 23, 2012 9:40 pm
- Forum: Technical Help
- Topic: 85 NQ50 problems starting...
- Replies: 16
- Views: 6846
Re: 85 NQ50 problems starting...
Yeah it was pretty d*** loud, i dont think i ran it long enough to burn a ring, i bet it wasnt even 5 seconds before i turned the switch off, it was smoking really bad when it fired up so i shut it off, just wanted to test that it would start
- Tue Oct 23, 2012 7:58 pm
- Forum: Technical Help
- Topic: 85 NQ50 problems starting...
- Replies: 16
- Views: 6846
Re: 85 NQ50 problems starting...
Keep in mind everytime i tried to restart it, even after taking the exhaust off again, i removed the plug and cleaned it with cumbustion chamber cleaner and then reinstalled the plug and then tried to start it
- Tue Oct 23, 2012 7:41 pm
- Forum: Technical Help
- Topic: 85 NQ50 problems starting...
- Replies: 16
- Views: 6846
Re: 85 NQ50 problems starting...
The pipe has plenty of flow, and it doesnt start anymore even when i took te exhaust off and tried to start it again.....
- Tue Oct 23, 2012 7:10 pm
- Forum: Technical Help
- Topic: 85 NQ50 problems starting...
- Replies: 16
- Views: 6846
Re: 85 NQ50 problems starting...
I pulled the plug and cranked it a few times and nothing came out
- Tue Oct 23, 2012 7:05 pm
- Forum: Technical Help
- Topic: 85 NQ50 problems starting...
- Replies: 16
- Views: 6846
Re: 85 NQ50 problems starting...
Thanks for the info, gonna try it tomorrow, hopefully thats all it is, it had oil in the oil tank bout 1/4 to 1/2 full before i took it off and cleaned it out and changed the oil...when i started getting this thing back on the road (or attempting to anyways)
- Tue Oct 23, 2012 6:46 pm
- Forum: Technical Help
- Topic: 85 NQ50 problems starting...
- Replies: 16
- Views: 6846
Re: 85 NQ50 problems starting...
A little more info, its an 85 nq50, the air box assembly is all the way on, will it do me any good to take the head off and clean the head with a sandblaster to clear it all off(the inside of the top of the cylinder head where the spark plug goes in), i have a blaster cabinet, i believe its a bead b...
- Tue Oct 23, 2012 4:45 pm
- Forum: Technical Help
- Topic: 85 NQ50 problems starting...
- Replies: 16
- Views: 6846
85 NQ50 problems starting...
Ok i used the search feature and couldnt find an answer that matched my problem, so here it is.... has compression, has a good starter, new battery, new spark plug, getting gas, engine has been sitting for years and years, has new air cleaner, has manual petcock with a cap on the intake suction poin...
- Thu Oct 18, 2012 11:52 am
- Forum: Wanted / For Sale
- Topic: Trustworthy traders......
- Replies: 239
- Views: 168116
Re: Trustworthy traders......
MopedMark is an awesome trader......got all the parts as described, answered all my questions quickly (REALLY quickly) and awesome pacaging job
Now i have another scooter back on the road
Now i have another scooter back on the road