Search found 74 matches

by DrZ34
Tue Aug 21, 2007 9:52 pm
Forum: Technical Help
Topic: Not getting spark
Replies: 39
Views: 11521

yes
by DrZ34
Mon Aug 20, 2007 6:52 pm
Forum: Technical Help
Topic: 84 thru 87 spree owner needed
Replies: 6
Views: 2894

Or i can look at mine 4 you L8tr this week
by DrZ34
Sun Aug 19, 2007 3:52 pm
Forum: Technical Help
Topic: Not getting spark
Replies: 39
Views: 11521

try switching the PRIMARY side of the coil , if the coil is hooked up backwards it will spark however very much reduced output
by DrZ34
Fri Aug 17, 2007 4:23 pm
Forum: Performance Technical
Topic: Would this Work On A 85 NQ50/spree ?
Replies: 9
Views: 4860

no over rev on top?

MIne is ported w/ a different carb and piped
by DrZ34
Mon Aug 06, 2007 2:42 pm
Forum: Technical Help
Topic: Petcock Leaking and Dies Under Throttle
Replies: 14
Views: 6930

Not for nothing check the polarity on the primary side of the coil. It WILL run if there bakwards but the coil will overheat (also a smaller but runnable spark, that may miss underload)
by DrZ34
Sun Aug 05, 2007 7:04 pm
Forum: General Discussion
Topic: Recommendation in SF bay Area to work on '84 Spree
Replies: 2
Views: 1261

DONT DO THAT. The best way is to impact gun off the nut and use a slide hammer, fingers facing outward like to remove a bearing. napa rents them
by DrZ34
Sat Aug 04, 2007 5:53 pm
Forum: General Discussion
Topic: MSD coil upgrade.
Replies: 0
Views: 2029

MSD coil upgrade.

In the advanced section there was a topic about this said item . I work @ a NAPA and we carry (and/or can get) this item . Matter of fact I have one on the table next to me!! GOTO you local napa and give them this part ## 7357225. or if you have to order it thru napa by the MSD # it is 8207 SPEC lin...
by DrZ34
Mon Jul 30, 2007 5:52 pm
Forum: Technical Help
Topic: Elite pulley mod?
Replies: 11
Views: 4544

I saw somewhere that an sb shares (some parts) with a spree. So would a crank swap work?
by DrZ34
Mon Jul 30, 2007 4:31 pm
Forum: General Discussion
Topic: ****Official Picture Post****
Replies: 947
Views: 469953

Obligitory Odo Post


All but like 5mi. on original motor!!
by DrZ34
Mon Jul 30, 2007 4:11 pm
Forum: Performance Technical
Topic: aerodynamic
Replies: 1
Views: 1649

Small Turn signals from a big bike , the usually Illegal too small ones on big bikes. They are how ever kosher on a spree, Remover the reflectors on the front fender and pu them there. http://i209.photobucket.com/albums/bb114/Z344Door/0730071604-00.jpg Like that! Oh and then remove the Ghey stock on...
by DrZ34
Mon Jul 30, 2007 3:57 pm
Forum: Technical Help
Topic: Reed valves
Replies: 6
Views: 2238

well if you have a smaall gap , flip them over they should be symetrical. NO more gap
It can't hurt
by DrZ34
Sun Jul 29, 2007 3:34 pm
Forum: Technical Help
Topic: Reed valves
Replies: 6
Views: 2238

The reason they say check for gap is (I think) because there supposed to be none. But when you screw the reed/reed stopper to the reed block there shouldn't be any tension ramming the reed to the seat (read bent reeds)
by DrZ34
Sun Jul 29, 2007 3:29 pm
Forum: Performance Technical
Topic: Would this Work On A 85 NQ50/spree ?
Replies: 9
Views: 4860

I mean I PROBABLY will get a box like that anyway. But I will test my mods w/ a stock cdi then the "uncorked" cdi

And OBV. post my findings :shock: :lol:
by DrZ34
Sun Jul 29, 2007 3:28 pm
Forum: Performance Technical
Topic: Would this Work On A 85 NQ50/spree ?
Replies: 9
Views: 4860

Well I shot the seller a question and here was the reply Hi, yes this CDI will work on the spree. because the spree does not have the rev potential that other honda scooters have (elite, aero, etc) the performance improvement will not be as dramatic on the spree. But If I modded a spree to make it m...