Search found 256 matches

by harleyracer59
Sat Mar 09, 2024 6:21 am
Forum: General Discussion
Topic: Custom Wheels
Replies: 22
Views: 11323

Re: Custom Wheels

You could always buy some Japan alloy wheels. They’re 4x110? Bolt pattern and a ruckus/zoomer rear hub bolts to them and for front i use the elite 150 front hub. Same bolt pattern. But it has 105mm diameter drum brake. For upgraded stopping power.
by harleyracer59
Fri Feb 02, 2024 11:34 pm
Forum: Technical Help
Topic: 85 Gyro S carburetor issue
Replies: 11
Views: 4177

Re: 85 Gyro S carburetor issue

If I remember correctly. The axle just bolts into a bearing that’s pressed into case. Here’s am 85 piece and it’s cheaper. I’ve had a few gyros down to bare cases. That side cover just bolts onto the engine cases. You have to remove that cover to get the cooling fan off. And remove the flywheel and ...
by harleyracer59
Wed Jan 31, 2024 9:40 pm
Forum: Technical Help
Topic: 85 Gyro S carburetor issue
Replies: 11
Views: 4177

Re: 85 Gyro S carburetor issue

Left rear wheel is the coaster side. What was your issue? I have some spare parts and will help you any way I can. I owe you for those parts that helped me out a couple years ago. 😉 Exact problem not yet diagnosed. Noticed the wheel showing some wobble. Wheel is bolted securely to the brake drum, b...
by harleyracer59
Sat Jan 13, 2024 3:24 am
Forum: Technical Help
Topic: 85 Gyro S carburetor issue
Replies: 11
Views: 4177

Re: 85 Gyro S carburetor issue

hey mike. check your float level... too high will caue your exact issue.. lower it a 1/2 a mmm and see if it fixes your problem i dont think you have a jetting issue Okay...good stuff HR59...and seems to make sense. Will keep this in mind next March when I pull the Gyro out of storage. Had a proble...
by harleyracer59
Sat Jan 13, 2024 3:17 am
Forum: Scooter Showcase
Topic: Honda Lead NH50
Replies: 67
Views: 202969

Re: Honda Lead NH50

I would get a complete gy6 racing pulley with vented clutch bell off fleabay. It’s the zx diameter pulley with different groove choices a red contra spring new clutch with red clutch springs and a vented clutch bell. Easiest and best and cheapest option in my opinion. When you get it. Take it apart ...
by harleyracer59
Sat Dec 30, 2023 5:59 pm
Forum: Scooter Showcase
Topic: Honda Lead NH50
Replies: 67
Views: 202969

Re: Honda Lead NH50

It was 38mm lenght and there was a hole 12mm. I had to drill to 14mm to fit it to af18e. And with lenght Im still waiting for malossi belt and zx pulley. its this vari: https://www.2hmoto.cz/variator-ip000337 if i remember correctly, a racing gy6 rear pulley is the same diameter as the zx pulley an...
by harleyracer59
Sat Dec 23, 2023 5:52 pm
Forum: Scooter Showcase
Topic: Honda Lead NH50
Replies: 67
Views: 202969

Re: Honda Lead NH50

stock cvt vs in-part ( i had to drill boss)... and do you think that i should grind case more in that spot? thank you what are the measurements on the variator boss? i had to drill out the dio variator boss to fit on my ab07. with my newly found info on the pgo star1. malossi and polini both make v...
by harleyracer59
Fri Dec 22, 2023 5:40 pm
Forum: Technical Help
Topic: 85 Gyro S carburetor issue
Replies: 11
Views: 4177

Re: 85 Gyro S carburetor issue

hey mike. check your float level... too high will caue your exact issue.. lower it a 1/2 a mmm and see if it fixes your problem i dont think you have a jetting issue
by harleyracer59
Fri Dec 22, 2023 5:25 pm
Forum: Scooter Showcase
Topic: Honda Lead NH50
Replies: 67
Views: 202969

Re: Honda Lead NH50

harleyracer59: i was talking about between flywheel and pickup coil (from the outside). Some bikes have in service manual gap between these two parts... usuallly 0,45mm https://i.ibb.co/BZT3HT1/s-l1200.jpg its been a while since ive had a flywheel off one of my hondas... lol for some reason i was p...
by harleyracer59
Sun Dec 10, 2023 6:15 pm
Forum: Scooter Showcase
Topic: 1984 Gen 1 Aero Build
Replies: 6
Views: 1784

Re: 1984 Gen 1 Aero Build

Parts list I used a Malossi Gyro cylinder for the Japanese TG50 spec engine. Based on this Treatland review, it is the same stroke as the Gen 1 Aero: https://www.treatland.tv/malossi-70cc-47mm-cylinder-for-honda-GYRO-TG50-and-p/malossi-gyro-kit-31-6170.htm "ports look like af01 ports. which is...
by harleyracer59
Sun Dec 10, 2023 5:31 pm
Forum: Builder's workshop
Topic: AF05e with AF16 crank ?
Replies: 10
Views: 10183

Re: AF05e with AF16 crank ?

Its probably an af16e or af18e with an af05e rear trans cover... i think this is the correct answer to what engine is in this guys scooter. looking at that last pic he poste, 2 thingsverified that its for sure not a spree af05. 1, it has a 4 bolt reed block intake, spree engine only has a 2 bolt. 2...
by harleyracer59
Sun Dec 10, 2023 2:26 am
Forum: Scooter Showcase
Topic: Honda Lead NH50
Replies: 67
Views: 202969

Re: Honda Lead NH50

I’m sure there Is it but I think it’s kinda fixed. I don’t know how you would adjust? Your stator is bolted down centered around the flywheel shaft. I’ve used an offset woodruff key to adjust base timing. But the crankshaft flywheel and stator are all self centered by bearings and cases.
by harleyracer59
Sat Dec 02, 2023 6:38 pm
Forum: Scooter Showcase
Topic: Honda Lead NH50
Replies: 67
Views: 202969

Re: Honda Lead NH50

Modified ab07 cases to fit af01 lead bbk
by harleyracer59
Sat Dec 02, 2023 6:36 pm
Forum: Scooter Showcase
Topic: Honda Lead NH50
Replies: 67
Views: 202969

Re: Honda Lead NH50

I have never seen a lead in person but I have learned a fair amount about them in my searching for 83-84 ab07 aero performance. For the engine mount. Search what others have done to put a dio in a first Gen aero. I actually modified a set of ab07 cases so I could port match a lead af01 big bore on i...
by harleyracer59
Sat Dec 02, 2023 8:06 am
Forum: Performance Technical
Topic: 83-84 aero nb50 AB07 engine big bore cylinder: finally found!!!!!
Replies: 0
Views: 8013

83-84 aero nb50 AB07 engine big bore cylinder: finally found!!!!!

:2thumbs: That’s right folks. And this ain’t clickbate. After years of research and all the nay saying. I have found a bolt on big bore kit for the first generation aero 50 owners. And there’s multiple big name company’s making these kits, like Malossi and polini just to name a few. There is a scoot...