Search found 256 matches
- Sat Mar 09, 2024 6:21 am
- Forum: General Discussion
- Topic: Custom Wheels
- Replies: 22
- Views: 11727
Re: Custom Wheels
You could always buy some Japan alloy wheels. They’re 4x110? Bolt pattern and a ruckus/zoomer rear hub bolts to them and for front i use the elite 150 front hub. Same bolt pattern. But it has 105mm diameter drum brake. For upgraded stopping power.
- Fri Feb 02, 2024 11:34 pm
- Forum: Technical Help
- Topic: 85 Gyro S carburetor issue
- Replies: 11
- Views: 4441
Re: 85 Gyro S carburetor issue
If I remember correctly. The axle just bolts into a bearing that’s pressed into case. Here’s am 85 piece and it’s cheaper. I’ve had a few gyros down to bare cases. That side cover just bolts onto the engine cases. You have to remove that cover to get the cooling fan off. And remove the flywheel and ...
- Wed Jan 31, 2024 9:40 pm
- Forum: Technical Help
- Topic: 85 Gyro S carburetor issue
- Replies: 11
- Views: 4441
Re: 85 Gyro S carburetor issue
Left rear wheel is the coaster side. What was your issue? I have some spare parts and will help you any way I can. I owe you for those parts that helped me out a couple years ago. 😉 Exact problem not yet diagnosed. Noticed the wheel showing some wobble. Wheel is bolted securely to the brake drum, b...
- Sat Jan 13, 2024 3:24 am
- Forum: Technical Help
- Topic: 85 Gyro S carburetor issue
- Replies: 11
- Views: 4441
Re: 85 Gyro S carburetor issue
hey mike. check your float level... too high will caue your exact issue.. lower it a 1/2 a mmm and see if it fixes your problem i dont think you have a jetting issue Okay...good stuff HR59...and seems to make sense. Will keep this in mind next March when I pull the Gyro out of storage. Had a proble...
- Sat Jan 13, 2024 3:17 am
- Forum: Scooter Showcase
- Topic: Honda Lead NH50
- Replies: 74
- Views: 210049
Re: Honda Lead NH50
I would get a complete gy6 racing pulley with vented clutch bell off fleabay. It’s the zx diameter pulley with different groove choices a red contra spring new clutch with red clutch springs and a vented clutch bell. Easiest and best and cheapest option in my opinion. When you get it. Take it apart ...
- Sat Dec 30, 2023 5:59 pm
- Forum: Scooter Showcase
- Topic: Honda Lead NH50
- Replies: 74
- Views: 210049
Re: Honda Lead NH50
It was 38mm lenght and there was a hole 12mm. I had to drill to 14mm to fit it to af18e. And with lenght Im still waiting for malossi belt and zx pulley. its this vari: https://www.2hmoto.cz/variator-ip000337 if i remember correctly, a racing gy6 rear pulley is the same diameter as the zx pulley an...
- Sat Dec 23, 2023 5:52 pm
- Forum: Scooter Showcase
- Topic: Honda Lead NH50
- Replies: 74
- Views: 210049
Re: Honda Lead NH50
stock cvt vs in-part ( i had to drill boss)... and do you think that i should grind case more in that spot? thank you what are the measurements on the variator boss? i had to drill out the dio variator boss to fit on my ab07. with my newly found info on the pgo star1. malossi and polini both make v...
- Fri Dec 22, 2023 5:40 pm
- Forum: Technical Help
- Topic: 85 Gyro S carburetor issue
- Replies: 11
- Views: 4441
Re: 85 Gyro S carburetor issue
hey mike. check your float level... too high will caue your exact issue.. lower it a 1/2 a mmm and see if it fixes your problem i dont think you have a jetting issue
- Fri Dec 22, 2023 5:25 pm
- Forum: Scooter Showcase
- Topic: Honda Lead NH50
- Replies: 74
- Views: 210049
Re: Honda Lead NH50
harleyracer59: i was talking about between flywheel and pickup coil (from the outside). Some bikes have in service manual gap between these two parts... usuallly 0,45mm https://i.ibb.co/BZT3HT1/s-l1200.jpg its been a while since ive had a flywheel off one of my hondas... lol for some reason i was p...
- Sun Dec 10, 2023 6:15 pm
- Forum: Scooter Showcase
- Topic: 1984 Gen 1 Aero Build
- Replies: 6
- Views: 1927
Re: 1984 Gen 1 Aero Build
Parts list I used a Malossi Gyro cylinder for the Japanese TG50 spec engine. Based on this Treatland review, it is the same stroke as the Gen 1 Aero: https://www.treatland.tv/malossi-70cc-47mm-cylinder-for-honda-GYRO-TG50-and-p/malossi-gyro-kit-31-6170.htm "ports look like af01 ports. which is...
- Sun Dec 10, 2023 5:31 pm
- Forum: Builder's workshop
- Topic: AF05e with AF16 crank ?
- Replies: 10
- Views: 10874
Re: AF05e with AF16 crank ?
Its probably an af16e or af18e with an af05e rear trans cover... i think this is the correct answer to what engine is in this guys scooter. looking at that last pic he poste, 2 thingsverified that its for sure not a spree af05. 1, it has a 4 bolt reed block intake, spree engine only has a 2 bolt. 2...
- Sun Dec 10, 2023 2:26 am
- Forum: Scooter Showcase
- Topic: Honda Lead NH50
- Replies: 74
- Views: 210049
Re: Honda Lead NH50
I’m sure there Is it but I think it’s kinda fixed. I don’t know how you would adjust? Your stator is bolted down centered around the flywheel shaft. I’ve used an offset woodruff key to adjust base timing. But the crankshaft flywheel and stator are all self centered by bearings and cases.
- Sat Dec 02, 2023 6:38 pm
- Forum: Scooter Showcase
- Topic: Honda Lead NH50
- Replies: 74
- Views: 210049
Re: Honda Lead NH50
Modified ab07 cases to fit af01 lead bbk
- Sat Dec 02, 2023 6:36 pm
- Forum: Scooter Showcase
- Topic: Honda Lead NH50
- Replies: 74
- Views: 210049
Re: Honda Lead NH50
I have never seen a lead in person but I have learned a fair amount about them in my searching for 83-84 ab07 aero performance. For the engine mount. Search what others have done to put a dio in a first Gen aero. I actually modified a set of ab07 cases so I could port match a lead af01 big bore on i...
- Sat Dec 02, 2023 8:06 am
- Forum: Performance Technical
- Topic: 83-84 aero nb50 AB07 engine big bore cylinder: finally found!!!!!
- Replies: 0
- Views: 8661
83-84 aero nb50 AB07 engine big bore cylinder: finally found!!!!!
:2thumbs: That’s right folks. And this ain’t clickbate. After years of research and all the nay saying. I have found a bolt on big bore kit for the first generation aero 50 owners. And there’s multiple big name company’s making these kits, like Malossi and polini just to name a few. There is a scoot...