Search found 19 matches

by jranilovich
Tue Sep 29, 2020 1:32 pm
Forum: Technical Help
Topic: HONDA SPREE CLUTCH ADVICE FOR REBUILD
Replies: 2
Views: 165

Re: HONDA SPREE CLUTCH ADVICE FOR REBUILD

Awesome thanks for the info i will check them out...
by jranilovich
Fri Sep 18, 2020 8:28 am
Forum: Technical Help
Topic: HONDA SPREE CLUTCH ADVICE FOR REBUILD
Replies: 2
Views: 165

HONDA SPREE CLUTCH ADVICE FOR REBUILD

Some one have some information PLEASE,, So i have been trying to reline and rebuild a couple clutches i have for a couple stock honda sprees i have.. I had a clutch rebuilt by JW and when they regreased the bearing he put so much grease in it once i rode it grease slung all over the new clutch pads ...
by jranilovich
Wed Apr 08, 2020 8:27 am
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

Update , Figured i would wright this real quick in hopes that it helps someone ,and or saves them the pain i went through. So long story short it turned out that one of the cylinders that i replaced was worn out, it was that one thing i didn't think twice about untill i had done everything possible ...
by jranilovich
Mon Mar 23, 2020 10:49 am
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

Hi All, I'm starting to pull my hair out i have checked compression getting close to 140psi, checked the idle jet numerous times, checked both crank case seals and bearings,have good spark, tried good know CDI,i even tried taking the complete carb off my perfectly good running spree and put it onto ...
by jranilovich
Fri Jan 03, 2020 2:51 pm
Forum: Technical Help
Topic: Hard starting. Crank seal leak
Replies: 4
Views: 2616

Re: Hard starting. Crank seal leak

thistleb wrote:
Sat Oct 12, 2019 10:18 am
Definitely leaking. My son noticed air escaping from the left side cover when cranking. Pulled cover and confirmed leaking from the seal. Will you replace that now.
What is the Easiest way to tell if the seal is leaking soapy water and trying to start it?
by jranilovich
Fri Jan 03, 2020 2:44 pm
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

i have not figured out the rattle yet it got to cold up here to ride it so im going to wait untill spring and get back into it i will keep you posted on what i find.. Please let me know if you find anything on yours,, all the info i can find the better..
by jranilovich
Thu Oct 24, 2019 8:14 am
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

Update. So i have been able to rebuild the top end on all 3 of my Sprees, All with honda parts, And i have come to the conclusion that one of them has an underlying problem that i can't seem to nail down. 2 out of the 3 start no problem all i have to do is hit the start button and they fire up. My o...
by jranilovich
Tue Sep 10, 2019 8:19 am
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

Ok So after some Crazy busy weeks i finally can give ya an update. After all is said and done the rebuild was a great success thanks to all the help eclark5483. after rebuilding the motor i found the cause for the wicked vibration the bearing in the tranmission cover was allowing in and out movement...
by jranilovich
Mon Aug 19, 2019 3:42 pm
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

That should improve after breaking it in. Gotta let the new rings seat a bit and that extra oil kind of throws off your fuel mix a bit. Wait till the break in is finished and you are back to a regular mix of just pump and gas and then see where you are at. Awesome that was kind of what i thought bu...
by jranilovich
Mon Aug 19, 2019 8:49 am
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

Hi All, So i Finally got my honda Rings this weekend (after waiting 3 weeks)..I cleaned up the cylinder which came out great all the rough edges on the exhaust port was just carbon build up it cleaned up real nice...I will add pictures tomorow i Left my phone at home.Once i got everything back togth...
by jranilovich
Sun Aug 11, 2019 10:49 pm
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

Just let me know how much ... I really appreciate it..
by jranilovich
Sun Aug 11, 2019 10:48 pm
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

Sounds good I'll take both if you dont care I have another spree that I'm going to rebuild after this one and it will need the top end rebuilt too...
by jranilovich
Sun Aug 11, 2019 7:13 pm
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

That would be very nice just let me know wich one you think is the best and how much and I will do it..

and lastly other than premixed 80:1 for the first 2 tanks..

How does one properly break in new rings and piston??
by jranilovich
Sun Aug 11, 2019 4:40 pm
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

I'd go probably 2 tanks with an extra 80:1. These Spree piston kits get a bad rap, and for the most part, rightfully so. But you must consider, whenever you install a new piston and rings, the engine is going to generate a lot more heat until the rings and the cylinder wall have married each other....
by jranilovich
Fri Aug 09, 2019 8:04 am
Forum: Technical Help
Topic: 1986 nq50 hard to get started
Replies: 38
Views: 10678

Re: 1986 nq50 hard to get started

Did you add extra oil in the tank for break in, in addition to the pump? 80:1 In the tank to help the piston seat right. I wouldn't try a rehone, probably won't help, but for sure use a Honda brand piston and rings. I didn't add extra oil i never thought about that. 80:1 for first couple tanks?? or...