Search found 21 matches
- Tue Aug 03, 2021 8:42 am
- Forum: Technical Help
- Topic: Spree - Slow Take Off AFTER engine warms up
- Replies: 6
- Views: 2855
Re: Spree - Slow Take Off AFTER engine warms up
Since you don't relate to scooter terms yet, newb... The bystarter is a thermo-reactive valve that controls the "choke" system on the carburetor. It has two wires, two screws holding it on, with a horseshoe retainer. it can be tested with an Ohm-meter. The service manual gives the value, ...
- Thu May 13, 2021 2:37 pm
- Forum: General Discussion
- Topic: HONDA SPREE WIKI PAGE
- Replies: 13
- Views: 6940
HONDA SPREE WIKI PAGE
Does any one know what happened to the wiki page??
Been down for a while, is it coming back ever?
Been down for a while, is it coming back ever?
- Tue Sep 29, 2020 1:32 pm
- Forum: Technical Help
- Topic: HONDA SPREE CLUTCH ADVICE FOR REBUILD
- Replies: 2
- Views: 2071
Re: HONDA SPREE CLUTCH ADVICE FOR REBUILD
Awesome thanks for the info i will check them out...
- Fri Sep 18, 2020 8:28 am
- Forum: Technical Help
- Topic: HONDA SPREE CLUTCH ADVICE FOR REBUILD
- Replies: 2
- Views: 2071
HONDA SPREE CLUTCH ADVICE FOR REBUILD
Some one have some information PLEASE,, So i have been trying to reline and rebuild a couple clutches i have for a couple stock honda sprees i have.. I had a clutch rebuilt by JW and when they regreased the bearing he put so much grease in it once i rode it grease slung all over the new clutch pads ...
- Wed Apr 08, 2020 8:27 am
- Forum: Technical Help
- Topic: 1986 nq50 hard to get started
- Replies: 38
- Views: 26100
Re: 1986 nq50 hard to get started
Update , Figured i would wright this real quick in hopes that it helps someone ,and or saves them the pain i went through. So long story short it turned out that one of the cylinders that i replaced was worn out, it was that one thing i didn't think twice about untill i had done everything possible ...
- Mon Mar 23, 2020 10:49 am
- Forum: Technical Help
- Topic: 1986 nq50 hard to get started
- Replies: 38
- Views: 26100
Re: 1986 nq50 hard to get started
Hi All, I'm starting to pull my hair out i have checked compression getting close to 140psi, checked the idle jet numerous times, checked both crank case seals and bearings,have good spark, tried good know CDI,i even tried taking the complete carb off my perfectly good running spree and put it onto ...
- Fri Jan 03, 2020 2:51 pm
- Forum: Technical Help
- Topic: Hard starting. Crank seal leak
- Replies: 4
- Views: 5131
- Fri Jan 03, 2020 2:44 pm
- Forum: Technical Help
- Topic: 1986 nq50 hard to get started
- Replies: 38
- Views: 26100
Re: 1986 nq50 hard to get started
i have not figured out the rattle yet it got to cold up here to ride it so im going to wait untill spring and get back into it i will keep you posted on what i find.. Please let me know if you find anything on yours,, all the info i can find the better..
- Thu Oct 24, 2019 8:14 am
- Forum: Technical Help
- Topic: 1986 nq50 hard to get started
- Replies: 38
- Views: 26100
Re: 1986 nq50 hard to get started
Update. So i have been able to rebuild the top end on all 3 of my Sprees, All with honda parts, And i have come to the conclusion that one of them has an underlying problem that i can't seem to nail down. 2 out of the 3 start no problem all i have to do is hit the start button and they fire up. My o...
- Tue Sep 10, 2019 8:19 am
- Forum: Technical Help
- Topic: 1986 nq50 hard to get started
- Replies: 38
- Views: 26100
Re: 1986 nq50 hard to get started
Ok So after some Crazy busy weeks i finally can give ya an update. After all is said and done the rebuild was a great success thanks to all the help eclark5483. after rebuilding the motor i found the cause for the wicked vibration the bearing in the tranmission cover was allowing in and out movement...
- Mon Aug 19, 2019 3:42 pm
- Forum: Technical Help
- Topic: 1986 nq50 hard to get started
- Replies: 38
- Views: 26100
Re: 1986 nq50 hard to get started
That should improve after breaking it in. Gotta let the new rings seat a bit and that extra oil kind of throws off your fuel mix a bit. Wait till the break in is finished and you are back to a regular mix of just pump and gas and then see where you are at. Awesome that was kind of what i thought bu...
- Mon Aug 19, 2019 8:49 am
- Forum: Technical Help
- Topic: 1986 nq50 hard to get started
- Replies: 38
- Views: 26100
Re: 1986 nq50 hard to get started
Hi All, So i Finally got my honda Rings this weekend (after waiting 3 weeks)..I cleaned up the cylinder which came out great all the rough edges on the exhaust port was just carbon build up it cleaned up real nice...I will add pictures tomorow i Left my phone at home.Once i got everything back togth...
- Sun Aug 11, 2019 10:49 pm
- Forum: Technical Help
- Topic: 1986 nq50 hard to get started
- Replies: 38
- Views: 26100
Re: 1986 nq50 hard to get started
Just let me know how much ... I really appreciate it..
- Sun Aug 11, 2019 10:48 pm
- Forum: Technical Help
- Topic: 1986 nq50 hard to get started
- Replies: 38
- Views: 26100
Re: 1986 nq50 hard to get started
Sounds good I'll take both if you dont care I have another spree that I'm going to rebuild after this one and it will need the top end rebuilt too...
- Sun Aug 11, 2019 7:13 pm
- Forum: Technical Help
- Topic: 1986 nq50 hard to get started
- Replies: 38
- Views: 26100
Re: 1986 nq50 hard to get started
That would be very nice just let me know wich one you think is the best and how much and I will do it..
and lastly other than premixed 80:1 for the first 2 tanks..
How does one properly break in new rings and piston??
and lastly other than premixed 80:1 for the first 2 tanks..
How does one properly break in new rings and piston??