Search found 16 matches

by Spreezer
Wed Jul 10, 2019 2:34 pm
Forum: Technical Help
Topic: NQ50 hydro-lock
Replies: 11
Views: 2075

Re: NQ50 hydro-lock

Wish I could say got it running like a top, but can't. Tried cleaning the carb again, tried spraying premix directly, and even starter fluid but no cigar, just an occasional backfire.
Had to move on. Thanks again for the help guys.
John if you see this, good luck, and safe riding.
Spreezer
by Spreezer
Sun Jul 07, 2019 3:10 pm
Forum: Technical Help
Topic: NQ50 hydro-lock
Replies: 11
Views: 2075

Re: NQ50 hydro-lock

Ok it started. Used drill and spray bottle. Thanks for the help couldn't have done it without.
Photo...
Image
by Spreezer
Thu Jul 04, 2019 12:39 am
Forum: Technical Help
Topic: Spree Spark Plug Gap
Replies: 5
Views: 3731

Re: Spree Spark Plug Gap

Which is .635 mm
by Spreezer
Mon Jul 01, 2019 8:38 pm
Forum: Technical Help
Topic: NQ50 hydro-lock
Replies: 11
Views: 2075

Re: NQ50 hydro-lock

Thanks for info. My gasket looks like this .... Photo https://i.postimg.cc/Vkd8q8Tw/IMG-20190701-160031.jpg And had some aluminum tape for exhaust...photo https://i.postimg.cc/dVmR0XRK/IMG-20190701-192842.jpg Found throttle cable was seized so had to free it up. Filled with PB Blaster and got lucky....
by Spreezer
Mon Jul 01, 2019 4:57 pm
Forum: Technical Help
Topic: NQ50 hydro-lock
Replies: 11
Views: 2075

Re: NQ50 hydro-lock

Anxious to just try it at this point but my exhaust gasket has no outer material like the one in noiseguys gasket kit.
by Spreezer
Mon Jul 01, 2019 3:37 pm
Forum: Technical Help
Topic: NQ50 hydro-lock
Replies: 11
Views: 2075

Re: NQ50 hydro-lock

Maybe I'll run the meatball premix first method to make sure oil pump is primed. And just suck on petcock vacumn to fill carb. It's not been rebuilt so oil mix should be?
by Spreezer
Mon Jul 01, 2019 3:12 pm
Forum: Technical Help
Topic: NQ50 hydro-lock
Replies: 11
Views: 2075

Re: NQ50 hydro-lock

Drained. Everything cleaned. Left cylinder etc alone Never touched oil pump or intake manifold. Baked exhaust in chimenea and hope to reuse gasket. 3 small holes in pipe, 2 in fin. Wrap it? Searching for best first start attempt procedure. Have a spray bottle Photos.. https://i.postimg.cc/155wBnMF/I...
by Spreezer
Mon Jul 01, 2019 12:55 am
Forum: Technical Help
Topic: NQ50 hydro-lock
Replies: 11
Views: 2075

Re: NQ50 hydro-lock

That would have been about 3 years worth. Here is all that was left after the last tip-over.. photo
Image
by Spreezer
Thu Jun 27, 2019 12:18 am
Forum: Technical Help
Topic: NQ50 hydro-lock
Replies: 11
Views: 2075

NQ50 hydro-lock

Found my '84 was hydro-locked. Am draining per meatballs post. It's working.
Photo...
Image
by Spreezer
Wed Jun 26, 2019 12:42 am
Forum: Technical Help
Topic: NQ50 H will not start
Replies: 12
Views: 2261

Re: NQ50 H will not start

Thanks for that. I'm on it.
by Spreezer
Tue Jun 25, 2019 1:53 am
Forum: Technical Help
Topic: NQ50 H will not start
Replies: 12
Views: 2261

Re: NQ50 H will not start

Or maybe meatballs via oil pump?
by Spreezer
Tue Jun 25, 2019 1:28 am
Forum: Technical Help
Topic: NQ50 H will not start
Replies: 12
Views: 2261

Re: NQ50 H will not start

I'll take eclark5483s advice from another post
by Spreezer
Tue Jun 25, 2019 1:22 am
Forum: Technical Help
Topic: NQ50 H will not start
Replies: 12
Views: 2261

Re: NQ50 H will not start

Nailed it for me. Any more advice for draining crankcase? I could turn it upside down or remove engine. It's half apart now. Could take the intake out.
by Spreezer
Tue Jun 25, 2019 1:09 am
Forum: Technical Help
Topic: How many hoses go to carb?
Replies: 5
Views: 1108

Re: How many hoses go to carb?

I'm so knowledgable now after reading the wiki I'll even add that since you mention it the 2 from the petcock serve to get Fuel to the carb. The lower thinner hose draws vacuum which allows the upper thicker hose to deliver the fuel via the design of the petcock.
by Spreezer
Sun Jun 23, 2019 5:16 pm
Forum: Technical Help
Topic: How many hoses go to carb?
Replies: 5
Views: 1108

Re: How many hoses go to carb?

Mind you, my carb is still attached to the intake so I am referencing those hoses as well.