Wish I could say got it running like a top, but can't. Tried cleaning the carb again, tried spraying premix directly, and even starter fluid but no cigar, just an occasional backfire.
Had to move on. Thanks again for the help guys.
John if you see this, good luck, and safe riding.
Spreezer
Search found 16 matches
- Wed Jul 10, 2019 2:34 pm
- Forum: Technical Help
- Topic: NQ50 hydro-lock
- Replies: 11
- Views: 5533
- Sun Jul 07, 2019 3:10 pm
- Forum: Technical Help
- Topic: NQ50 hydro-lock
- Replies: 11
- Views: 5533
- Thu Jul 04, 2019 12:39 am
- Forum: Technical Help
- Topic: Spree Spark Plug Gap
- Replies: 5
- Views: 7016
Re: Spree Spark Plug Gap
Which is .635 mm
- Mon Jul 01, 2019 8:38 pm
- Forum: Technical Help
- Topic: NQ50 hydro-lock
- Replies: 11
- Views: 5533
Re: NQ50 hydro-lock
Thanks for info. My gasket looks like this .... Photo https://i.postimg.cc/Vkd8q8Tw/IMG-20190701-160031.jpg And had some aluminum tape for exhaust...photo https://i.postimg.cc/dVmR0XRK/IMG-20190701-192842.jpg Found throttle cable was seized so had to free it up. Filled with PB Blaster and got lucky....
- Mon Jul 01, 2019 4:57 pm
- Forum: Technical Help
- Topic: NQ50 hydro-lock
- Replies: 11
- Views: 5533
Re: NQ50 hydro-lock
Anxious to just try it at this point but my exhaust gasket has no outer material like the one in noiseguys gasket kit.
- Mon Jul 01, 2019 3:37 pm
- Forum: Technical Help
- Topic: NQ50 hydro-lock
- Replies: 11
- Views: 5533
Re: NQ50 hydro-lock
Maybe I'll run the meatball premix first method to make sure oil pump is primed. And just suck on petcock vacumn to fill carb. It's not been rebuilt so oil mix should be?
- Mon Jul 01, 2019 3:12 pm
- Forum: Technical Help
- Topic: NQ50 hydro-lock
- Replies: 11
- Views: 5533
Re: NQ50 hydro-lock
Drained. Everything cleaned. Left cylinder etc alone Never touched oil pump or intake manifold. Baked exhaust in chimenea and hope to reuse gasket. 3 small holes in pipe, 2 in fin. Wrap it? Searching for best first start attempt procedure. Have a spray bottle Photos.. https://i.postimg.cc/155wBnMF/I...
- Mon Jul 01, 2019 12:55 am
- Forum: Technical Help
- Topic: NQ50 hydro-lock
- Replies: 11
- Views: 5533
- Thu Jun 27, 2019 12:18 am
- Forum: Technical Help
- Topic: NQ50 hydro-lock
- Replies: 11
- Views: 5533
- Wed Jun 26, 2019 12:42 am
- Forum: Technical Help
- Topic: NQ50 H will not start
- Replies: 12
- Views: 5741
Re: NQ50 H will not start
Thanks for that. I'm on it.
- Tue Jun 25, 2019 1:53 am
- Forum: Technical Help
- Topic: NQ50 H will not start
- Replies: 12
- Views: 5741
Re: NQ50 H will not start
Or maybe meatballs via oil pump?
- Tue Jun 25, 2019 1:28 am
- Forum: Technical Help
- Topic: NQ50 H will not start
- Replies: 12
- Views: 5741
Re: NQ50 H will not start
I'll take eclark5483s advice from another post
- Tue Jun 25, 2019 1:22 am
- Forum: Technical Help
- Topic: NQ50 H will not start
- Replies: 12
- Views: 5741
Re: NQ50 H will not start
Nailed it for me. Any more advice for draining crankcase? I could turn it upside down or remove engine. It's half apart now. Could take the intake out.
- Tue Jun 25, 2019 1:09 am
- Forum: Technical Help
- Topic: How many hoses go to carb?
- Replies: 5
- Views: 3295
Re: How many hoses go to carb?
I'm so knowledgable now after reading the wiki I'll even add that since you mention it the 2 from the petcock serve to get Fuel to the carb. The lower thinner hose draws vacuum which allows the upper thicker hose to deliver the fuel via the design of the petcock.
- Sun Jun 23, 2019 5:16 pm
- Forum: Technical Help
- Topic: How many hoses go to carb?
- Replies: 5
- Views: 3295
Re: How many hoses go to carb?
Mind you, my carb is still attached to the intake so I am referencing those hoses as well.