Search found 411 matches
- Wed Sep 09, 2009 8:20 am
- Forum: Technical Help
- Topic: Spree (Nifty 50 here in NZ) - POOR RUNNING!! HELP!
- Replies: 31
- Views: 7645
Re: Spree (Nifty 50 here in NZ) - POOR RUNNING!! HELP!
When you remove all of the jets, particularly the low speed circuit, you should visually be able to inspect the jet in particular the jet orifice, the hole should be perfectly round. You were not clear whether you actually stuck the guitar wire through the jet orifice. Noiseguy pointed out that you ...
- Tue Sep 08, 2009 9:28 pm
- Forum: General Chit-Chat
- Topic: New 2010 Buell Blast
- Replies: 8
- Views: 2354
Re: New 2010 Buell Blast
My wife bought a 2003 Blast last summer for cheap. It had 670 miles on it. She is 5'3" and has the high seat. she can stand flat footed easily. It has electric start. Runs about 90 mph stock. It has great brakes and starts putting out power above idle and doesn't quit till the rev limiter. The ...
- Tue Sep 08, 2009 10:06 am
- Forum: Performance Technical
- Topic: 2000 SA50P jet and throttle cable questions
- Replies: 23
- Views: 7946
Re: 2000 SA50P jet and throttle cable questions
bleeding off too much pressure by opening up the back of the exhaust can reduce the resonance of the exhaust and make less power.
- Mon Sep 07, 2009 7:11 pm
- Forum: Scooter Showcase
- Topic: Elite E SB50 with SE50 implant
- Replies: 17
- Views: 14101
Re: Elite E SB50 with SE50 implant
I was surprised that the plastic bushings would hold up to the welding. Nice adaptator mount. and jig. .... the mount uses two urethane bushings in the front, and the stock "goose head" piece, i just cut it off of the old mount, put it in my fixture and welded it up. the best part is that ...
- Sun Sep 06, 2009 9:17 pm
- Forum: Technical Help
- Topic: AF05 problems - tuning my 92 elite
- Replies: 57
- Views: 9466
Re: AF05 problems - tuning my 92 elite
If removing the air filter hurts performance then usually you are too rich.
Only change one thing at a time. Changing jetting and springs is way too confusing.
Only change one thing at a time. Changing jetting and springs is way too confusing.
- Sun Sep 06, 2009 8:24 pm
- Forum: Performance Technical
- Topic: CHT measurement via electronic meters
- Replies: 36
- Views: 9663
Re: CHT measurement via electronic meters
Mouse I can't check this out till later. I am on vacation at the moment. No scooters no bikes with speedometers just two dirt bikes. Thanks for the direct link. mousewheels wrote:... I'm interested in the type of thermocouple wire the Trail Tech Vapor uses. Did not find that info in the manual on th...
- Sun Sep 06, 2009 8:24 pm
- Forum: Advanced Tech Docs
- Topic: CHT measurement via electronic meters
- Replies: 21
- Views: 27541
Re: CHT measurement via electronic meters
Mouse I can't check this out till later. I am on vacation at the moment. No scooters no bikes with speedometers just two dirt bikes. Thanks for the direct link. mousewheels wrote:... I'm interested in the type of thermocouple wire the Trail Tech Vapor uses. Did not find that info in the manual on th...
- Sat Sep 05, 2009 11:01 am
- Forum: Performance Technical
- Topic: CHT measurement via electronic meters
- Replies: 36
- Views: 9663
Re: CHT measurement via electronic meters
Mouse do you mean as in measure the voltage a various known temperatures? such as 32 and 212┬░F? Are these bi-metal electrodes? I have a temperature gauge on my trail tech vapor and it has two wires coming out of it. Two conductors of differing alloys, welded at the tip. Photo shows a Fluke brand th...
- Sat Sep 05, 2009 11:01 am
- Forum: Advanced Tech Docs
- Topic: CHT measurement via electronic meters
- Replies: 21
- Views: 27541
Re: CHT measurement via electronic meters
Mouse do you mean as in measure the voltage a various known temperatures? such as 32 and 212┬░F? Are these bi-metal electrodes? I have a temperature gauge on my trail tech vapor and it has two wires coming out of it. Two conductors of differing alloys, welded at the tip. Photo shows a Fluke brand th...
- Fri Sep 04, 2009 2:19 pm
- Forum: Performance Technical
- Topic: CHT measurement via electronic meters
- Replies: 36
- Views: 9663
Re: CHT measurement via electronic meters
Are these bi-metal electrodes? I have a temperature gauge on my trail tech vapor and it has two wires coming out of it.
- Fri Sep 04, 2009 2:19 pm
- Forum: Advanced Tech Docs
- Topic: CHT measurement via electronic meters
- Replies: 21
- Views: 27541
Re: CHT measurement via electronic meters
Are these bi-metal electrodes? I have a temperature gauge on my trail tech vapor and it has two wires coming out of it.
- Fri Sep 04, 2009 2:14 pm
- Forum: Scooter Showcase
- Topic: Project Tempest (SpreeTypeR)
- Replies: 73
- Views: 53373
Re: Project SpreeTypeR
Will the new MSD spark unit provide multiple sparks per revolution? If so do you have to retard the timing?
- Fri Sep 04, 2009 8:47 am
- Forum: Performance Technical
- Topic: Dustbin Elite.... Ever seen one?
- Replies: 2
- Views: 775
Re: Dustbin Elite.... Ever seen one?
The color was because it was near sunset and also perhaps because the fairing was dirty with cheap black enamel overspray. I only added paint over the front wheel using gimp. I have spent hours with rubbing compound yesterday and I do have a much blacker fairing. What is that - Shadow replacement wi...
- Thu Sep 03, 2009 10:20 pm
- Forum: Performance Technical
- Topic: Dustbin Elite.... Ever seen one?
- Replies: 2
- Views: 775
Dustbin Elite.... Ever seen one?
I haven't seen one either but through the magic of photography I made one. ![Image](http://www.veloliner.com/elite50e/rtsideelite82209aero.jpg)
![Image](http://www.veloliner.com/elite50e/rtsideelite82209aero.jpg)
- Thu Sep 03, 2009 10:10 pm
- Forum: Scooter Showcase
- Topic: Elite E SB50 with SE50 implant
- Replies: 17
- Views: 14101
Re: Elite E SB50 with SE50 implant
I elongated my standard eliteE mount. Used a couple of pieces of 3/4" square 16ga tubes and welded them to the sides of the sides of of the stock mount. Then added a half inch tube to go between them and a 3/8"x6" bolts to hold it together. My motor is mounted at about the location of...