Search found 232 matches

by harleyracer59
Fri Apr 10, 2020 2:20 am
Forum: Technical Help
Topic: Request for input - Parts Spree 84/85 vs 86/87 and SB50
Replies: 42
Views: 43186

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

good eye mike, I didn't even pick up on the tire part. lol
hope youre good and staying healthy! take care
by harleyracer59
Thu Apr 09, 2020 11:21 pm
Forum: Technical Help
Topic: Request for input - Parts Spree 84/85 vs 86/87 and SB50
Replies: 42
Views: 43186

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

yes. they both are 95mm drum brakes and shaft and spline count are the same on early dios. I think I read here at a certain year the changed the shaft diameter. I don't remember what year though. I believe variated af05 axle shafts are the same a 93-98? dio. I don't remember if its 98 or later. I ha...
by harleyracer59
Thu Apr 09, 2020 11:13 pm
Forum: Technical Help
Topic: 1985 Honda Gyro starter issues
Replies: 14
Views: 2171

Re: 1985 Honda Gyro starter issues

the problem is gyro spins backwards from the rest of the honda scooters. I cant tell in your pic but the side with the wire stitching up should look lie a mirrored image of the other side. the wire should connect to a brush like the other side and those brushes slide into the little tracks verticall...
by harleyracer59
Wed Apr 08, 2020 10:23 pm
Forum: Technical Help
Topic: 1985 Honda Gyro starter issues
Replies: 14
Views: 2171

Re: 1985 Honda Gyro starter issues

lightly sand the brush faces, a light scrub over the center shaft faces commutator? a dollop of grease in the back bearing cavity, slap it back together. that wire that sticking up should be connected to something. I cant remember of the top of my head. but youre missing something. the one terminal ...
by harleyracer59
Sun Apr 05, 2020 4:15 am
Forum: Technical Help
Topic: Honda gyro Leaking Oil
Replies: 44
Views: 9907

Re: Honda gyro Leaking Oil

glad to hear it man. so the honda seal was of a larger OD? Did you measure the new seal to see how far off the # was?
by harleyracer59
Wed Mar 25, 2020 4:05 pm
Forum: Technical Help
Topic: NH80 - Removing drive gear for crank seal replacement
Replies: 12
Views: 2885

Re: NH80 - Removing drive gear for crank seal replacement

do these carbs have an electric bystarter or that goofy heater hoses to and from the head setup? have you thought of swapping/ upgrading the carb for something newer, bigger, better performing, easier to get parts for? I know in Europe they make spigot adapters that'll bolt to the manifold and allow...
by harleyracer59
Tue Mar 24, 2020 5:29 pm
Forum: Technical Help
Topic: NH80 - Removing drive gear for crank seal replacement
Replies: 12
Views: 2885

Re: NH80 - Removing drive gear for crank seal replacement

that sounds like an interesting trip. glad to hear you got it handled. and that's cool you gave him a tip anyways. im sure that was a good move, probably why he had no problem showing you how to pull the crank seals by pulling yours. and im sure if you ever need to go back, he will be just as friend...
by harleyracer59
Mon Mar 23, 2020 3:09 am
Forum: Technical Help
Topic: How do I connect this Spree oil line? (pic)
Replies: 6
Views: 1683

Re: How do I connect this Spree oil line? (pic)

the fitting/elbow on the tank will be hard to match, so if that elbow is not dry rotted or cracked clean and reuse it. go to local auto parts store. in the help isle, youll buy vacuum hose fitting assortment then get 2-3ft of 5/16? vacuum/windshield washer fluid hose. its cheaper and easier to pump ...
by harleyracer59
Sat Mar 21, 2020 10:34 pm
Forum: Technical Help
Topic: How do I connect this Spree oil line? (pic)
Replies: 6
Views: 1683

Re: How do I connect this Spree oil line? (pic)

take one of those fittings out of one side and push that hose onto the other hose with fitting. looks like you have 2 union fittings. you only need 1
by harleyracer59
Sat Mar 21, 2020 10:31 pm
Forum: Technical Help
Topic: Honda gyro Leaking Oil
Replies: 44
Views: 9907

Re: Honda gyro Leaking Oil

I think the u shaped line is correct. it was/is clear. goes between the pump and the intake manifold. plug/cap these two nipples once line is removed. I think its 40:1 but id search for a definitive answer. can you post the # you pulled off the seal? it should look something like 5+- X 15+- X 4+-? r...
by harleyracer59
Sat Mar 21, 2020 5:01 pm
Forum: Technical Help
Topic: Honda gyro Leaking Oil
Replies: 44
Views: 9907

Re: Honda gyro Leaking Oil

I searched a little last night. I know people have rebuilt the oil pumps before. and from what I remember. the pumps are pretty much similar. the big difference on the gyro being its longer shaft. but the shaft diameter is thw same I believe. ill look around my mess today. I know I have an oil pump ...
by harleyracer59
Fri Mar 20, 2020 10:17 pm
Forum: Technical Help
Topic: Another Fuel related question
Replies: 15
Views: 3517

Re: Another Fuel related question

check for a vacuum leak between manifold and carburetor do you have the spacer installed correctly? it only goes one way and has arrow pointing up
by harleyracer59
Tue Mar 17, 2020 4:25 pm
Forum: Technical Help
Topic: NH80 - Removing drive gear for crank seal replacement
Replies: 12
Views: 2885

Re: NH80 - Removing drive gear for crank seal replacement

question for anyone with a good explanation.. why were these aero 80's, first gen aero 50 ab07, and I believe the aero 125's a non-splined crank output shaft and work fine and don't slip yet the second gen aero 50 af05e splined crankshafts slip, strip the splines and become useless?
by harleyracer59
Tue Mar 17, 2020 4:17 pm
Forum: Technical Help
Topic: NH80 - Removing drive gear for crank seal replacement
Replies: 12
Views: 2885

Re: NH80 - Removing drive gear for crank seal replacement

use a steering wheel puller. and maybe a little heat. they press on to a slight taper. like the 83-84 aero 50. theres no keyway to keep them from spinning.
by harleyracer59
Wed Mar 11, 2020 3:17 pm
Forum: Performance Technical
Topic: Big Bore with stock Intake and exhaust?
Replies: 6
Views: 3732

Re: Big Bore with stock Intake and exhaust?

I agree with this guy^^^^. the key is to ask questions. study old posts and use the knowledge to your advantage. if you have trouble, make a thread and give all the info you can for your situation. that will net you faster more complete answers and hopefully solutions to your problems. if you big bo...