Search found 155 matches
- Thu May 21, 2015 5:22 am
- Forum: Scooter Showcase
- Topic: Ministroke Taida 43.4 ministroke + Corsa fun
- Replies: 25
- Views: 18093
Re: Ministroke Taida 43.4 ministroke + Corsa fun
split case and breathe in those little aluminum flakes for a few hours! http://i1068.photobucket.com/albums/u447/rustansouza/Kit%20bike%20build/0508151817_zpso7cuoeiu.jpg before http://i1068.photobucket.com/albums/u447/rustansouza/Kit%20bike%20build/0508151745c_zpseh07hdcz.jpg after http://i1068.pho...
- Thu May 21, 2015 5:12 am
- Forum: Scooter Showcase
- Topic: Ministroke Taida 43.4 ministroke + Corsa fun
- Replies: 25
- Views: 18093
Re: Ministroke Taida 43.4 ministroke + Corsa fun
remove motor and everything else http://i1068.photobucket.com/albums/u447/rustansouza/Kit%20bike%20build/0429151827_zpsa65byklq.jpg http://i1068.photobucket.com/albums/u447/rustansouza/Kit%20bike%20build/0508151728_zpsws88tg6d.jpg http://i1068.photobucket.com/albums/u447/rustansouza/Kit%20bike%20bui...
- Thu May 21, 2015 5:05 am
- Forum: Scooter Showcase
- Topic: Ministroke Taida 43.4 ministroke + Corsa fun
- Replies: 25
- Views: 18093
Re: Ministroke Taida 43.4 ministroke + Corsa fun
cleaning everything up http://i1068.photobucket.com/albums/u447/rustansouza/Kit%20bike%20build/0429151744_zpskg7ehpx6.jpg http://i1068.photobucket.com/albums/u447/rustansouza/Kit%20bike%20build/0429151745_zpsquuvsjcn.jpg http://i1068.photobucket.com/albums/u447/rustansouza/Kit%20bike%20build/0429151...
- Thu May 21, 2015 5:02 am
- Forum: Scooter Showcase
- Topic: Ministroke Taida 43.4 ministroke + Corsa fun
- Replies: 25
- Views: 18093
Ministroke Taida 43.4 ministroke + Corsa fun
another build. specs: SYM DD50 block Ported polini corsa Ported Ctblack manifold Ported Taida ministroke crank 7.9 gearing Kelli Pulley SEF Ramp Kelli Heavy Clutch 28OKO carb. BMF V8 exhaust ZX transmission heres the beginning: all dirty 8K miles! http://i1068.photobucket.com/albums/u447/rustansouza...
- Sat May 16, 2015 5:18 pm
- Forum: Scooter Showcase
- Topic: Dirty 98 Elite- updated thread throughout
- Replies: 79
- Views: 48289
Re: Dirty 98 Elite- updated thread throughout
Sweet! Pauly you must have some special lucky corsa. I could only hit 12,700 on the dyno, no wind resistance, on a heavily ported corsa, on 110, with a pipe that hits 1800rpm higher than the scorp. The scorpion peaks at about 8500. Its lower than you'd think. The scorpion, is designed for taiwan bo...
- Fri Apr 10, 2015 5:30 pm
- Forum: Performance Technical
- Topic: Fabrizi 50mm Squish
- Replies: 29
- Views: 15347
Re: Fabrizi 50mm Squish
i think the calculator assumes you are raising the top of the exhaust port and not cutting down the top of the cylinder.
- Mon Mar 09, 2015 10:54 pm
- Forum: Scooter Showcase
- Topic: Re: Dio disc brake front on Elite frame
- Replies: 38
- Views: 51134
Re: Dio disc brake front on Elite frame
Then cut the top for correct size of metro stem and install bearing cup. IMAG0850 - Copy.jpg Before moving on, the metro uses a larger bearing on the bottom than the elite, so remove the lower bearing race from the metro stem carefully and replace it with a new (you have to order one from honda) el...
- Sun Mar 08, 2015 3:46 pm
- Forum: Performance Technical
- Topic: 28mm oko carb tuning
- Replies: 5
- Views: 4440
Re: 28mm oko carb tuning
adjust needle clip
- Sat Mar 07, 2015 5:44 pm
- Forum: Scooter Showcase
- Topic: SYM DD50 porting project
- Replies: 27
- Views: 16636
Re: SYM DD50 porting project
thanks,
sometimes gotta go through the case to make it just right.
quicksteel good stuff for fill in. resistant to chemicals.
sometimes gotta go through the case to make it just right.
quicksteel good stuff for fill in. resistant to chemicals.
- Sat Mar 07, 2015 1:01 am
- Forum: Scooter Showcase
- Topic: SYM DD50 porting project
- Replies: 27
- Views: 16636
Re: SYM DD50 porting project
yup that is the stock corsa aluminum base gasket.DirtyE wrote:Nice. Is that matched to a base gasket?
lines up really nice with stock af16 but DD50 needs to be opened up a bit to line up perfect.
- Fri Mar 06, 2015 5:00 pm
- Forum: Scooter Showcase
- Topic: SYM DD50 porting project
- Replies: 27
- Views: 16636
Re: SYM DD50 porting project
finished
- Fri Mar 06, 2015 4:59 pm
- Forum: Scooter Showcase
- Topic: SYM DD50 porting project
- Replies: 27
- Views: 16636
Re: SYM DD50 porting project
small side case ugly flow so needs to be cleaned up also
- Fri Mar 06, 2015 4:55 pm
- Forum: Scooter Showcase
- Topic: SYM DD50 porting project
- Replies: 27
- Views: 16636
Re: SYM DD50 porting project
and then cut again
- Fri Mar 06, 2015 4:53 pm
- Forum: Scooter Showcase
- Topic: SYM DD50 porting project
- Replies: 27
- Views: 16636
Re: SYM DD50 porting project
next step match case to corsa cylinder.
dd50 needs more work than AF16, but can still make nice flow.
dd50 needs more work than AF16, but can still make nice flow.
- Fri Mar 06, 2015 4:48 pm
- Forum: Scooter Showcase
- Topic: SYM DD50 porting project
- Replies: 27
- Views: 16636
Re: SYM DD50 porting project
thanks again for the calculator. will definitley learn how to use it and apply for future builds.