Search found 143 matches
- Wed Apr 25, 2012 9:48 pm
- Forum: Performance Technical
- Topic: AF16E not quite right
- Replies: 22
- Views: 7627
Re: AF16E not quite right
This is my pic of pre test run with 7's in the vari. I will be trying to do a run tomorrow if its not wet out or raining. But what do ya think im getting the belt fairly high.
- Tue Apr 24, 2012 11:18 pm
- Forum: Performance Technical
- Topic: AF16E not quite right
- Replies: 22
- Views: 7627
Re: AF16E not quite right
Ill take a pic tomorrow after a couple of runs
- Tue Apr 24, 2012 10:55 pm
- Forum: Performance Technical
- Topic: AF16E not quite right
- Replies: 22
- Views: 7627
AF16E not quite right
Hello, My 87se is only topping out around 48mph about 2 weeks ago I had a run at 52mph. what would cause a change in 4mph and is there a way to get me cruising a little bit faster. Im running a 2001 AF16E with a malossi 72cc cast iron kit, intake and 24mm oko carb 135main 52 pilot. Pg short pipe(swi...
- Sun Jan 22, 2012 12:13 am
- Forum: Scooter Showcase
- Topic: Af16E for my 87Se?
- Replies: 7
- Views: 3588
Re: Af16E for my 87Se?
Ohh it was in my parts box and I just didnt take it off the table until after the pic
- Sun Jan 22, 2012 12:06 am
- Forum: Scooter Showcase
- Topic: Af16E for my 87Se?
- Replies: 7
- Views: 3588
Re: Af16E for my 87Se?
Stage one
Removal to a larger diameter. This is slightly ported compared to stock.
Removal to a larger diameter. This is slightly ported compared to stock.
- Sun Jan 22, 2012 12:03 am
- Forum: Scooter Showcase
- Topic: Af16E for my 87Se?
- Replies: 7
- Views: 3588
Re: Af16E for my 87Se?
This is a before of the intake.
- Sat Jan 21, 2012 11:53 pm
- Forum: Scooter Showcase
- Topic: Af16E for my 87Se?
- Replies: 7
- Views: 3588
Re: Af16E for my 87Se?
The starting components.
- Fri Jan 20, 2012 9:05 pm
- Forum: Scooter Showcase
- Topic: Af16E for my 87Se?
- Replies: 7
- Views: 3588
Af16E for my 87Se?
The past couple days Ive been slowly building the motor while waiting on parts for other projects. My plan started at swapping my 87 motor over to my 88 sa50 and to build the newer motor for my favorite ride. This af16e ran prior to dismemberment but not to the best standard. But its being updated w...
- Mon Jan 16, 2012 1:05 pm
- Forum: General Discussion
- Topic: secondary gear swap questions?
- Replies: 5
- Views: 1794
secondary gear swap questions?
Its my 01 AF16E motor and I was wondering what size press you guys had to use to push the rear shaft out of the gear?
Thanks
Thanks
- Sun Jan 15, 2012 2:51 pm
- Forum: General Discussion
- Topic: Part does not exist
- Replies: 14
- Views: 5429
Re: Part does not exist
So clean out the crude thats in it. check
- Sun Jan 15, 2012 2:16 pm
- Forum: General Discussion
- Topic: Part does not exist
- Replies: 14
- Views: 5429
Re: Part does not exist
But I also have a question about a little grove in the bearing raceway.
- Sun Jan 15, 2012 2:14 pm
- Forum: General Discussion
- Topic: Part does not exist
- Replies: 14
- Views: 5429
Re: Part does not exist
yep thats it. i have the cam it goes into the rear location but the front one is missing.
- Sat Jan 14, 2012 7:52 pm
- Forum: General Discussion
- Topic: Part does not exist
- Replies: 14
- Views: 5429
Re: Part does not exist
I had the cases sandblasted and when I got home and looked at it. I noticed that the peg was not there. Its not in any of my bags of hardware.
- Sat Jan 14, 2012 7:28 pm
- Forum: General Discussion
- Topic: Part does not exist
- Replies: 14
- Views: 5429
Part does not exist
Ive looked at two websites and the gentleman at Honda could not locate it on his screen. Im looking for the rear brake pin that bolts through the transmission. Not the one that attaches to the brake cable, the stationary pin. Any clues where to look or can I just replace it with a bolt and seal it u...
- Fri Apr 08, 2011 1:26 am
- Forum: General Discussion
- Topic: Vari CLutch
- Replies: 4
- Views: 1743
Re: Vari CLutch
What if its a 139qmb motor? Im going to try and see if I can convince him to let me try it out.