Search found 77 matches
- Sat Nov 14, 2020 9:35 am
- Forum: Technical Help
- Topic: Ch125 valve adjustment.
- Replies: 0
- Views: 2763
Ch125 valve adjustment.
Hey guys. Recently redid the top end on my ch125. Its ben running good all summer. Now its starting to act up so I decided to check the valve lash. Anyone familiar with the external adjustments on the cover? Manual says turn adjusters out and then in one degree on the dial. At TDC. Both of mine max ...
- Fri Nov 06, 2020 2:29 pm
- Forum: Technical Help
- Topic: Spree transmission bearing
- Replies: 8
- Views: 4102
Re: Spree transmission bearing
Hey.Noiseguys gaskets are OEM thickness. The bearing wasnt Completely seated in the cover. Now its perfect.... except she wont start..
- Sun Nov 01, 2020 8:30 pm
- Forum: Technical Help
- Topic: Spree transmission bearing
- Replies: 8
- Views: 4102
Re: Spree transmission bearing
Hey guys. Got the bearing pressed in and a new gasket from Noiseguy. Now when i close up the case the shaft binds up.. all i can think of is gasket to thin causin case to close to much?. Any advice thanks
- Thu Oct 22, 2020 8:08 pm
- Forum: Technical Help
- Topic: Spree transmission bearing
- Replies: 8
- Views: 4102
Re: Spree transmission bearing
Thanks man
- Thu Oct 22, 2020 2:17 pm
- Forum: Technical Help
- Topic: Spree transmission bearing
- Replies: 8
- Views: 4102
- Wed Oct 21, 2020 9:22 am
- Forum: Technical Help
- Topic: Spree transmission bearing
- Replies: 8
- Views: 4102
Re: Spree transmission bearing
Yep. I got the part number from the breakdown and unavailable through Babbits... andthat part number isnt anywhere on ebay.. thanks
- Tue Oct 20, 2020 7:28 pm
- Forum: Technical Help
- Topic: Spree transmission bearing
- Replies: 8
- Views: 4102
Spree transmission bearing
Hey guys. I have some lateral play in the shaft that the clutch bolt to. Is this normal. I took everything apart expecting to have a bearing that the tip rides in bit theres not one. Thanks
- Mon Sep 28, 2020 12:26 pm
- Forum: Technical Help
- Topic: HONDA SPREE CLUTCH ADVICE FOR REBUILD
- Replies: 2
- Views: 2097
Re: HONDA SPREE CLUTCH ADVICE FOR REBUILD
I had the same issue. The slots that the clutch springs clip into were wore out and stretched open. I got new springs and JB epoxy steel on the holes to stiffen up springs. Mich better now
- Mon Sep 28, 2020 9:26 am
- Forum: Technical Help
- Topic: Suddenly Spree dies on hills. Clueless
- Replies: 0
- Views: 2397
Suddenly Spree dies on hills. Clueless
Hey guys my old spree recently out of nowhere started stalling uphills and faster corners. New oiled filter. Sparkplug. Clean carb . Cleaned gastank. Fuel and vacum lines new. Tried new by starter. No changes.. im stumped. Anyone got anything?? Thanks
- Sun Aug 02, 2020 7:44 pm
- Forum: Technical Help
- Topic: Spree tire spin at idle
- Replies: 2
- Views: 2408
Re: Spree tire spin at idle
I’ve put a couple hundred miles on it since I got the clutch pads. belt is brand new ... springs are correct... the holes that The springs click into were stretched out real far so the springs were completely loose I could open the shoes with my hands ....I filled the holes with JB super steel putty...
- Fri Jul 31, 2020 5:32 pm
- Forum: Technical Help
- Topic: Spree tire spin at idle
- Replies: 2
- Views: 2408
Spree tire spin at idle
Hey guys. I got my spree clutch religned last year. The tire spins at idle still and the launch is very poor. Today i put in a set of yellow Leo Vince clutch springs. Still spins at idle.. i noticed the holes that the springs go into are stretched out. The springs just pop in and out easy.. any idea...
- Wed May 16, 2018 6:18 am
- Forum: Builder's workshop
- Topic: 1985 Honda spree clutch question
- Replies: 13
- Views: 11331
Re: 1985 Honda spree clutch question
Yes sent to jw clutch werks. Repadded. I have impact gun and vise. Im sure i can get it apart and replace the springs. It does seem like when it on the stand and you apply reae brake the motor rev does come down little bit
- Tue May 15, 2018 6:16 pm
- Forum: Builder's workshop
- Topic: 1985 Honda spree clutch question
- Replies: 13
- Views: 11331
Re: 1985 Honda spree clutch question
It spins when On the stand. If I come to a stop and just hold the back break IÔÇÖm good. I just got it all back together just going to send it
- Tue May 15, 2018 12:37 pm
- Forum: Builder's workshop
- Topic: 1985 Honda spree clutch question
- Replies: 13
- Views: 11331
Re: 1985 Honda spree clutch question
I did petcock and line never touched the carb.Is it easy to change the springs my self? I have no idea how to take apart
- Tue May 15, 2018 6:03 am
- Forum: Builder's workshop
- Topic: 1985 Honda spree clutch question
- Replies: 13
- Views: 11331
Re: 1985 Honda spree clutch question
I just had it religned and they didnt mention springs. They seem fine to me