Search found 129 matches
- Mon Feb 01, 2016 5:30 am
- Forum: Technical Help
- Topic: Engine questions
- Replies: 9
- Views: 4565
Re: Engine questions
Is this circlip position good?
- Sun Jan 31, 2016 11:28 pm
- Forum: Scooter Showcase
- Topic: '92 Dio SR Build
- Replies: 133
- Views: 75930
Re: '92 Dio SR Build
Thanks veedub, im going to look into that. I know for my car its possible to run 2 variants of heat ranges but i assume a bbk calls for a specific plug.
- Sun Jan 31, 2016 10:11 pm
- Forum: Scooter Showcase
- Topic: '92 Dio SR Build
- Replies: 133
- Views: 75930
Re: '92 Dio SR Build
Taz reccomends BPR6HS,
I have a few BR6HS, from what i have read the "P" stands for protected tip.
Not sure how important that is...
I have a few BR6HS, from what i have read the "P" stands for protected tip.
Not sure how important that is...
- Sun Jan 31, 2016 10:08 pm
- Forum: Technical Help
- Topic: Engine questions
- Replies: 9
- Views: 4565
Engine questions
1. Which position should the piston circlips sit at?
2. Should i use hondabond on the bore or head and if so won top or under the gasket?
2. Should i use hondabond on the bore or head and if so won top or under the gasket?
- Sun Jan 31, 2016 7:11 pm
- Forum: Scooter Showcase
- Topic: '92 Dio SR Build
- Replies: 133
- Views: 75930
Re: '92 Dio SR Build
The weather is a mess, its been hot but raining. Thanks for the compliment hopefully soon i can have some running videos.Ultraliner wrote:Must be hot in AU at the moment too, I hope you dropped a lemon wedge in that Corona
Your build is getting sweeter every day!
- Sun Jan 31, 2016 7:10 pm
- Forum: Scooter Showcase
- Topic: '92 Dio SR Build
- Replies: 133
- Views: 75930
Re: '92 Dio SR Build
I have a question on the 50mm tazland bore, what plug number will it take on a af16 vs af18 Is it difrence? Also what are the temp ranges on the bore? Highest, good idle area to shoot for? Jumps, Taz said it uses the same plug (lucky because i ordered 5). Heat range is max 275. I would heat cycle n...
- Sun Jan 31, 2016 2:17 am
- Forum: Scooter Showcase
- Topic: '92 Dio SR Build
- Replies: 133
- Views: 75930
Re: '92 Dio SR Build
ok so i'm on the home stretch now (i hope) took the advice and used loctite on the reed screws. https://farm2.staticflickr.com/1529/24697202076_e031dd32f5_z.jpg after sanding the CT base on the bench i then took some meat off to give a little less rubbing against the bore. https://farm2.staticflickr...
- Sat Jan 30, 2016 5:21 am
- Forum: Technical Help
- Topic: Heating gears
- Replies: 1
- Views: 1368
Re: Heating gears
Thanks! I wont beat either of them off.
For some odd reason most places here have only 10 tonne presses.
But i will find a 20 tonne
For some odd reason most places here have only 10 tonne presses.
But i will find a 20 tonne
- Fri Jan 29, 2016 1:39 am
- Forum: Technical Help
- Topic: af18e shroud clearance BBK
- Replies: 14
- Views: 7417
Re: af18e shroud clearance BBK
it does look crude but it allows the CT mani to fit and clears the bore.
- Fri Jan 29, 2016 1:37 am
- Forum: Scooter Showcase
- Topic: '92 Dio SR Build
- Replies: 133
- Views: 75930
Re: '92 Dio SR Build
hey jumps, so i took the tranny cover off again and double checked the seal, it seems the oil in the seal made it seem like it was broken, but it seems perfect for its age. so the oil plug arrived! https://farm2.staticflickr.com/1512/24589074401_29dc382575_z.jpg installed, please forgive the state o...
- Thu Jan 28, 2016 9:12 pm
- Forum: Scooter Showcase
- Topic: '92 Dio SR Build
- Replies: 133
- Views: 75930
Re: '92 Dio SR Build
jumps!
those are really good questions that i will talk to taz about. don't know why but i assumed it would run the oem plug.
but now that i think about it, it may need a cooler or hotter plug.
those are really good questions that i will talk to taz about. don't know why but i assumed it would run the oem plug.
but now that i think about it, it may need a cooler or hotter plug.
- Thu Jan 28, 2016 9:10 pm
- Forum: Technical Help
- Topic: af18e shroud clearance BBK
- Replies: 14
- Views: 7417
Re: af18e shroud clearance BBK
big help with the ct advice, i will do that this weekend when i loctite the reed screws.
i did bit of hacking last night to the left side shroud ( exit side ) i will upload a picture when i get a chance.
i did bit of hacking last night to the left side shroud ( exit side ) i will upload a picture when i get a chance.
- Thu Jan 28, 2016 4:52 pm
- Forum: Technical Help
- Topic: Heating gears
- Replies: 1
- Views: 1368
Heating gears
What is the concensus with heating gears in order to press them off for changeover?
- Thu Jan 28, 2016 4:41 am
- Forum: Technical Help
- Topic: af18e shroud clearance BBK
- Replies: 14
- Views: 7417
Re: af18e shroud clearance BBK
so im going to need to cut about 1/2 of the left shroud, to allow the ct mani to clear... https://farm2.staticflickr.com/1715/24638765266_66db3c118a_c.jpg the best idea i have had so far is to space it out this much so it doesnt make contact, is this too much to fill in with aliminum tape? https://f...
- Wed Jan 27, 2016 4:00 pm
- Forum: Performance Technical
- Topic: My new 114cc ac stroker build
- Replies: 10
- Views: 7897
Re: My new 114cc ac stroker build
This is gonna be great