Honda Spree and Elite 50 Forums

On a scoot, I don't know how stable you are you to make any mount. Haha. I can barely make sense of what's in my mirrors when I'm on the road, let alone a camera. I actually screwed a bolt into mirror mount for the camera and used one of the bolts for the floor board for the second video. So I gues...

Here's a couple short videos, I was testing a camera mount but it's too shaky.

http://youtu.be/BxXe6_mS7do

http://youtu.be/qf1IePgUSmM

Looks pretty sweet man; nice job! What's the performance like? Thanks, performance could be better but it's obviously a world of difference compared to a stock spree. It has low compression, I need to tear it down and see what It needs. Maybe I can get away with just a ring job, but might need a ne...

http://i50.photobucket.com/albums/f313/momovdub/Honda%20SPREE/DSC01485.jpg http://i50.photobucket.com/albums/f313/momovdub/Honda%20SPREE/DSC01476.jpg http://i50.photobucket.com/albums/f313/momovdub/Honda%20SPREE/DSC01465.jpg http://i50.photobucket.com/albums/f313/momovdub/Honda%20SPREE/DSC01482.jpg...

Decided to get some lighter variator rollers, stock rollers are 21g and I went down to 15g. Also did a little research and read that rounding the sharp edges of the ramp plate will help avoid roller wearing. So I did that with my dremel, using a little grinding stone. I still need a new drive belt, ...

Here's a pic of the manual valve installed, works great. I don't have a petcock cover so I'm not worried about it. But I do have a spare horn cover I might try to fit up. :lol: Also capped off the intake port with a rubber cap. I'm thinking I could use this port for a boost tube, maybe a future proj...

I bought a manual valve to replace my leaky petcock, not bad for $12 shipped.

Got the Mikuni installed and running, seems to run a lot better. Need to spend some time tuning this weekend. Still need to mess with the throttle cable and air filter box setup.

You are aware that the stock carb is an 18 mm carb? So 20 is not that much of an increase. As long as you keep the stock intake and reeds you improvement will be minimal A CT intake with a 24 or 26 OKO will boost your top speed well over 65 mph, possibly as much as 10 mph more than that. The first ...

I bought myself a Christmas preset, this Mikuni VM20 carb should get me running a little better.

I was able to get the Honda sticker off cleanly. Got some new prints of the face from Kinko's, looks a lot brighter and better.

It's all experimental right now, once it's riding weather again I plan on carrying a GPS with me and make marks on the speedo. Then I'll re-edit the face to be more accurate, might also have to do the same with on my stock spree (small wheel), if I decide to sell these. There's also the issue with t...

Made a Red face, tested it on my spare speedo.

I've been messing around with custom speedometer faces, increasing the MPH numbers. I scanned the stock face. http://i50.photobucket.com/albums/f313/momovdub/Honda%20SPREE/Picture-1-1.jpg http://i50.photobucket.com/albums/f313/momovdub/Honda%20SPREE/hondafinishedcluster2-1.jpg Printed it out and lam...

Cleaned it up, painted the rims and exhaust. Finally added a kickstand too. http://i50.photobucket.com/albums/f313/momovdub/Honda%20SPREE/DSC01246.jpg http://i50.photobucket.com/albums/f313/momovdub/Honda%20SPREE/DSC01250.jpg http://i50.photobucket.com/albums/f313/momovdub/Honda%20SPREE/DSC01262.jpg...