Search found 4761 matches
- Tue Jul 04, 2023 10:47 am
- Forum: General Discussion
- Topic: 1994 Honda SR Elite
- Replies: 7
- Views: 4170
Re: 1994 Honda SR Elite
Your question SEEMS to indicate that you expect there to be an oil drain plug on the engine case. My reply is : your bike has a 2-stroke engine that does not have ENGINE OIL. There is instead: 1. An oil tank that contains 2-stroke oil that is pumped and injected into the intake manifold for consump...
- Wed Jun 28, 2023 8:53 pm
- Forum: Technical Help
- Topic: Fuel petcock with "reserve"
- Replies: 10
- Views: 4464
Re: Fuel petcock with "reserve"
I think you might be shooting in the dark trying to find the petcock you describe. I certainly don't know of any. However, you can probably find a fitting to fit the threads on the tank, one that will allow you to have a short piece of hard line. Then, attach clear fuel line to that, and install an...
- Tue Jun 13, 2023 9:39 pm
- Forum: General Discussion
- Topic: 86 SPREE ....GOOD NEWS ...BAD NEWS
- Replies: 5
- Views: 3908
Re: 86 SPREE ....GOOD NEWS ...BAD NEWS
YES...that oil inlet is pulling air into the cylinder...a very bad thing...block it off.
- Thu Jun 01, 2023 12:58 pm
- Forum: General Discussion
- Topic: 85 spree
- Replies: 10
- Views: 4410
Re: 85 spree
I strongly advise against buying a Chinese replacement carburetor. In nearly ALL cases, the original carb can be cleaned and will perform reliably if done right. Chinese-made clones are sketchy in quality and often do not run well. Another thing you should do is replace ALL the fuel and vacuum line...
- Fri May 26, 2023 3:29 pm
- Forum: Technical Help
- Topic: new to forum
- Replies: 6
- Views: 1803
Re: new to forum
Fuel will ONLY flow through the line when engine is cranking or running. It takes vacuum from the engine in order for the petcock to open and allow flow.
- Fri May 26, 2023 12:37 pm
- Forum: Technical Help
- Topic: new to forum
- Replies: 6
- Views: 1803
Re: new to forum
I would begin with a very close inspection of the carburetor internally. Cleaning and verifying all the jets and passages as open and flowing. Checking the jet sizes and recording what i find. Then the gas tank and petcock, checking for rust and debris. Clean and de-rust if needed, and then install...
- Sun May 21, 2023 4:03 pm
- Forum: Technical Help
- Topic: Will not accelerate over 5mph!!
- Replies: 4
- Views: 863
- Thu May 18, 2023 7:17 pm
- Forum: General Discussion
- Topic: 1988 Honda Elite E Vacuum/Fuel Line Question
- Replies: 1
- Views: 3266
Re: 1988 Honda Elite E Vacuum/Fuel Line Question
Take a photo of the lines as they are now.
Remove the lines to be replaced.
Take the lines to the auto parts store, hardware store, or moto store and match them up with new lines.
Remove the lines to be replaced.
Take the lines to the auto parts store, hardware store, or moto store and match them up with new lines.
- Thu May 18, 2023 7:13 pm
- Forum: Technical Help
- Topic: Will not accelerate over 5mph!!
- Replies: 4
- Views: 863
Re: Will not accelerate over 5mph!!
Belt and/or variator weights and/or clutch
- Tue May 16, 2023 3:15 pm
- Forum: Scooter Showcase
- Topic: Honda Elite 80 Engine swap challenges
- Replies: 3
- Views: 3620
Re: Honda Elite 80 Engine swap challenges
I can confirm that the engine serial number is AFTER the year 2000,
but could not determine exact year.
Regarding the carburetor, I should think that swapping the old carb and intake to the newer engine
would be a good option to solve your issues with both air leaks and cable connection.
but could not determine exact year.
Regarding the carburetor, I should think that swapping the old carb and intake to the newer engine
would be a good option to solve your issues with both air leaks and cable connection.
- Sun May 14, 2023 1:05 am
- Forum: Scooter Showcase
- Topic: Re: Dio disc brake front on Elite frame
- Replies: 38
- Views: 54213
Re: Dio disc brake front on Elite frame
...well, it has been 8 years...
- Thu May 04, 2023 11:50 pm
- Forum: Builder's workshop
- Topic: Determining model year
- Replies: 2
- Views: 3189
Re: Determining model year
Hey there whc03grady ... :hi: Here are the VIN numbers to help you identify. 1985 VIN# 49 states = JH2AF060*FS100001-beginning number IOWA = JH2AF061*FS100001- 1985 engine # 49 states = AF06E-2100001 IOWA = AF05E-2100001 1986 Spree VIN# 49 states = JH2AF060*GS200001- IOWA = JH2AF061*GS200001- 1986 ...
- Thu May 04, 2023 11:59 am
- Forum: Technical Help
- Topic: AF05E ??
- Replies: 2
- Views: 682
Re: AF05E ??
It's a sure thing that the engine is the AF05E variated model that came in Aero 50 and early Elite 50.
- Mon May 01, 2023 1:16 pm
- Forum: General Discussion
- Topic: '85 Spree randomly died
- Replies: 15
- Views: 8824
- Mon Apr 24, 2023 6:35 pm
- Forum: Technical Help
- Topic: Gyro Oil Pump Repair
- Replies: 4
- Views: 993
Re: Gyro Oil Pump Repair
If anyone would know the inner workings of those it would be Dave (mousewheels). I can PM you his number if you want. Yeah, go ahead and share that. I'm not only trying to help a guy in NY with issue, but it looks like my own Gyro has developed similar problem. I've looked at a thread that mousewhe...