homemade crank puller
Moderator: Moderator
homemade crank puller
Hi forum. here's a homemade crank puller I made from a 4 inch C clamp from Harbor Freight, 1 1/4 black pipe from Home Depot, a couple washers, a couple nuts Home Depot. Total cost about 20 bucks. You will need a welder, Harbor Freight 99 bucks. or have someone weld it up for you.
- Attachments
-
- 20150201_061040.jpg (195.52 KiB) Viewed 8013 times
-
- 20150201_061132.jpg (188.48 KiB) Viewed 8013 times
-
- 20150201_061246.jpg (176.79 KiB) Viewed 8013 times
Last edited by ped on Sun Feb 01, 2015 12:18 pm, edited 1 time in total.
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
Re: homemade crank puller
not a welder. is long as you melt the metal you should be good.
this is not for something very important like a frame.
this is not for something very important like a frame.
- Attachments
-
- 20150201_081316.jpg (182.95 KiB) Viewed 8012 times
-
- 20150201_080224.jpg (155.5 KiB) Viewed 8012 times
-
- 20150201_075749.jpg (208.28 KiB) Viewed 8012 times
Last edited by ped on Sun Feb 01, 2015 12:04 pm, edited 1 time in total.
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
Re: homemade crank puller
the screw gets tightened down. And I turn on that flap. the black clamp part.
- Attachments
-
- 20150201_082228.jpg (181.29 KiB) Viewed 8012 times
-
- 20150201_082141.jpg (150.43 KiB) Viewed 8012 times
-
- 20150201_094430.jpg (171.15 KiB) Viewed 8012 times
Last edited by ped on Sun Feb 01, 2015 12:25 pm, edited 2 times in total.
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
Re: homemade crank puller
- Attachments
-
- 20150201_081939.jpg (186.23 KiB) Viewed 8011 times
-
- 20150201_082219.jpg (169.67 KiB) Viewed 8011 times
-
- 20150201_093634.jpg (198.93 KiB) Viewed 8011 times
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
Re: homemade crank puller
works great
- Attachments
-
- 20150201_093718.jpg (186.06 KiB) Viewed 8011 times
-
- 20150201_094245.jpg (159.77 KiB) Viewed 8011 times
-
- 20150201_081316.jpg (182.95 KiB) Viewed 8011 times
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
Re: homemade crank puller
it is weak metal casing where both crank seals..
Re: homemade crank puller
yes it is. It's best to heat up the bearings with a heat gun little bit.veedubh20 wrote:it is weak metal casing where both crank seals..
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
Re: homemade crank puller
01 Honda Elite S 120cc Taida H20
78 Honda Hobbit Athena
78 Honda Express/Hobbit Stage6/Athena LC 70
00 Gilera Runner PM Tuning 172
09 Aprillia SR50 Malossi Team MHR
81 Puch ZA50 Polini
71 CT70 Blue
79 Z50 Red
78 Honda Hobbit Athena
78 Honda Express/Hobbit Stage6/Athena LC 70
00 Gilera Runner PM Tuning 172
09 Aprillia SR50 Malossi Team MHR
81 Puch ZA50 Polini
71 CT70 Blue
79 Z50 Red
- Wheelman-111
- Moderator
- Posts: 11319
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: homemade crank puller
Greetings:
Very clever and useful work. Just to clarify; you heat the cases to enlarge the bearing sockets, and chill the bearings for easier insertion, right?
Very clever and useful work. Just to clarify; you heat the cases to enlarge the bearing sockets, and chill the bearings for easier insertion, right?
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Re: homemade crank puller
I freeze the crank first then slip the bearings on then freeze that. I put Hondabond on the cases then heat them with heat gun or torch. Then I hope they go together easily but when they don't I'll use this to complete the install.
01 Honda Elite S 120cc Taida H20
78 Honda Hobbit Athena
78 Honda Express/Hobbit Stage6/Athena LC 70
00 Gilera Runner PM Tuning 172
09 Aprillia SR50 Malossi Team MHR
81 Puch ZA50 Polini
71 CT70 Blue
79 Z50 Red
78 Honda Hobbit Athena
78 Honda Express/Hobbit Stage6/Athena LC 70
00 Gilera Runner PM Tuning 172
09 Aprillia SR50 Malossi Team MHR
81 Puch ZA50 Polini
71 CT70 Blue
79 Z50 Red
Re: homemade crank puller
Hi Whitey. that threaded rod is perfect.
Only needed to weld the two nuts together. any muffler shop can do that for you.
I went with the clamp because it had bigger threads. And looks a little stronger. But there's nothing wrong with the threaded rod. It was most likely less money and less work.
nice work
Only needed to weld the two nuts together. any muffler shop can do that for you.
I went with the clamp because it had bigger threads. And looks a little stronger. But there's nothing wrong with the threaded rod. It was most likely less money and less work.
nice work
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
Re: homemade crank puller
Hi forum.
I will soon get to test the puller again. Let you know how it goes.
I will soon get to test the puller again. Let you know how it goes.
- Attachments
-
- 20150313_171551.jpg (139.75 KiB) Viewed 7809 times
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
Re: homemade crank puller
Hecks yeah! What's your setup gunna be?? That looks like a high quality crank. What brand is it?
01 Honda Elite S 120cc Taida H20
78 Honda Hobbit Athena
78 Honda Express/Hobbit Stage6/Athena LC 70
00 Gilera Runner PM Tuning 172
09 Aprillia SR50 Malossi Team MHR
81 Puch ZA50 Polini
71 CT70 Blue
79 Z50 Red
78 Honda Hobbit Athena
78 Honda Express/Hobbit Stage6/Athena LC 70
00 Gilera Runner PM Tuning 172
09 Aprillia SR50 Malossi Team MHR
81 Puch ZA50 Polini
71 CT70 Blue
79 Z50 Red
- patthesoundguy
- Moderator
- Posts: 3159
- Joined: Mon Mar 29, 2010 11:38 am
- Location: Nova Scotia, Canada
- Contact:
Re: homemade crank puller
Wow what a great thread! Always great to have more tricks and designs for tools. I'm going to make a crank puller this summer for sure after seeing this thread
Dude! Ya Can't Fix Stupid!
84 Spree stock
84 Spree Dio AF18E MHR Cylinder Arrow Pipe 28mm OKO
80 Express, 47mm DR BBKit, Weak Ends Intake, Boyesen Dual stage reeds, 19mm Delorto carb, MLM pipe
79 Express
85 Aero 80 stock
84 elite 125 stock
84 Spree stock
84 Spree Dio AF18E MHR Cylinder Arrow Pipe 28mm OKO
80 Express, 47mm DR BBKit, Weak Ends Intake, Boyesen Dual stage reeds, 19mm Delorto carb, MLM pipe
79 Express
85 Aero 80 stock
84 elite 125 stock
Re: homemade crank puller
Hi Whitey. I see you notice. I havent decided on a setup. something for the street for sure.whitey wrote:Hecks yeah! What's your setup gunna be?? That looks like a high quality crank. What brand is it?
the crank is a ancient Chinese secret. Lol
land of the stroker cranks, where most affordable cranks come from. Taiwan.
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ