Honda Elite Sr 1994 build!!!!!!!!!

[Singo69]

I just got these gears in just wondering what they are capable of?
Are these a good set to go with?

[Bear45-70]

I didn't think anyone could take worse pictures than Wheelman, but I was wrong. If those are suppose to be gears, you could have fooled me.

[Trafficjamz]

18x39 is a 7.5 final ratio

If you have enuff power, those gears can push a scooter over 75mph.

at least 72cc and a nice pipe to even think about pushing them.

If you weigh over 200 lbs .....you may want to get a mini or full stroker to use those gears.

[Singo69]

I plan on running a 51mm bore with stock crank. and 28mm carb with ct mani and polini clutch

[veedubh20]

what pipe are you running?

Dont buy taiwan bore, get a polini.. just take your time, dont rush on project.

you can run S stock pipe,stock clutch, add center spring only.

[sum-azn-kid]

you should also get a keli vari and sef ramp. wat veedub said is true a $15 torque spring will do you more good than a $100+ clutch.

[Singo69]

its a tiawan bore no polini for me. i am running this pipe

[Singo69]

what size center spring?

[Singo69]

I didn't think anyone could take worse pictures than Wheelman, but I was wrong. If those are suppose to be gears, you could have fooled me.

sorry i wasnt asking for pic quality so

[sum-azn-kid]

i like to use a 1.5k torque spring it is a good mid ground. i had a 1k but it was crappy going up hill. how ever some people with the elite "s" trans like 2k because the rear pulley is tiny.
http://cgi.ebay.com/ebaymotors/Honda-Di ... leQ5fParts
the 1k will allow your rear pulley to close faster(get to top gear fast/less lowend pull) and 2k holds the low gear longer(more lowend pull but harder to get to your top gear/shifts back down quicker)
did you get a throttle cable for your carb?
http://cgi.ebay.com/ebaymotors/Dio-Sym- ... 2eb271eb2a
good luck on your build

[808BMW]

its a tiawan bore no polini for me. i am running this pipe

That's a lot of pipe for a stock crank, might want to step down to a smaller exhaust.

[veedubh20]

Today, I rode my 98 blk S

I had japan af18e motor. Rans Polini contesta, ct chrome, 24mm oko powerjet 45/130 - 1-1/2 turn out a/f screw. , Sr stock pipe. and 8.4 gear and 1k center spring. Complete stock clutch and bell. 42g (7g) , Keli pulley and keli ramp. Castor 927 oil , premix 32:1 to a gallon. 105lb rider.

Block is untouched port.

It ran good and lot of power..

[maddog]

the local term for your engine build is called "hamma jang"

[Spreetard]

(Hamajang) verb;

Definition: All messed up.
Source: Uncertain, could possibly have been derived from the Hawaiian word "hamama" meaning open. Or from the Hawaiian word "Hamale" meaning hammer. Actual lexical source is unknown.
Context: Used in common conversation among the local people of Hawaii.
Connotations: Negative, but is also used in a joking manner.
Examples: "That girl is hamajang." - "That girl is all messed up."
Sociological Implications: The word "hamajang" most likely developed from a need to describe something as incredibly altered in a negative way. It is possible that this word developed from a need or importance of describing the result of a physical fight within Hawaiian society.

Collected from: http://babel.uoregon.edu/slang/pub_sear ... s=detail01