Preping for BBK...
Moderator: Moderator
- mustangwagz
- Elite
- Posts: 483
- Joined: Sun Mar 21, 2010 9:10 pm
- Location: Western, PA
Preping for BBK...
Started tearin apart the spree tonight. Only got motor out and tore carb off. Decided i'd take another look at carb. Cleaned out bystarter passage seeing as i didnt get it good enough first time. Used a .030 Drill bit to clean passge.
* is the purpose of the emulision tube? and should i be able to push a wire whole way though it?
Next will be cleaning motor, and tearing off the major components. I wanna inspect reeds and make sure they're all gravy before i tear head N Jug off. Once its out ill check the Crank case for excessive oil pump leakage and then on to replacing stock parts with aftermarket parts!
Break in has me concerned but i've done alot of reading so hopefully all goes well! Ill get some pics of everything i'm doin and post em!
* is the purpose of the emulision tube? and should i be able to push a wire whole way though it?
Next will be cleaning motor, and tearing off the major components. I wanna inspect reeds and make sure they're all gravy before i tear head N Jug off. Once its out ill check the Crank case for excessive oil pump leakage and then on to replacing stock parts with aftermarket parts!
Break in has me concerned but i've done alot of reading so hopefully all goes well! Ill get some pics of everything i'm doin and post em!
-Zac
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
- martynkim
- Board Supporter
- Posts: 2899
- Joined: Tue Jan 05, 2010 10:22 pm
- Location: Tacoma, Washington
Re: Preping for BBK...
* is the purpose of the emulision tube? and should i be able to push a wire whole way though it?
Remove the tube by removing the jet. Then, Push a small object from the other side and remove the tube should pop right out. Then you will see a series of holes in the tube. find a music store, get some cuttings from a restringed guitar use the appropriate string (think it is E) and run it thru all openings reassemble. Should clean it right up. Good Luck Zac! LMK send email etc any other questions about this.
Remove the tube by removing the jet. Then, Push a small object from the other side and remove the tube should pop right out. Then you will see a series of holes in the tube. find a music store, get some cuttings from a restringed guitar use the appropriate string (think it is E) and run it thru all openings reassemble. Should clean it right up. Good Luck Zac! LMK send email etc any other questions about this.
Need parts? Parting out Spree Aero and Elite!
What people share about buying from me http://www.hondaspree.net/phpBB3/viewto ... =1&t=15559
PM me with your needs Cheap Parts
What people share about buying from me http://www.hondaspree.net/phpBB3/viewto ... =1&t=15559
PM me with your needs Cheap Parts
- mustangwagz
- Elite
- Posts: 483
- Joined: Sun Mar 21, 2010 9:10 pm
- Location: Western, PA
Re: Preping for BBK...
Took apart spree today and almost back together, gonna try millin head tomorrow. Prolly wont get it back together, got dad duty tomorrow. s***! lol
Anyhow, Emulision tube had major crap at the bottom of it.. but holes was clear n clean. So i fixed all that, cleaned it up and put back together. Carb should be problem free now other than the stupid bowl being stained in the bottom.
Reeds are allll good in the hood. had a piece of hair stuck on them though..figure that out? lol
Wrist pin bearing was only questionable thing i seen. I dont believe its toast, but we'll sell. I got lots of pics but just gotta figure out how to post more than 3 at a time! Grrr!
Also gettin new exhaust studs from work so thats a plus. Gona try to find stainless ones. "TRY!!" lol unless someone says otherwise.
Also, Oil pump doesnt seem to be leaking all that much if any.
I also made sure the EX on the piston was facing exhaust side of the jug! i read that somewhere and remembered it! Good call eh? as far as rings, thats a no brainer..Piston gots little dowel pin lookin things in it for the rings to nestle into. BRILLIANT!! lol ill get pics on ASAP!!
Anyhow, Emulision tube had major crap at the bottom of it.. but holes was clear n clean. So i fixed all that, cleaned it up and put back together. Carb should be problem free now other than the stupid bowl being stained in the bottom.
Reeds are allll good in the hood. had a piece of hair stuck on them though..figure that out? lol
Wrist pin bearing was only questionable thing i seen. I dont believe its toast, but we'll sell. I got lots of pics but just gotta figure out how to post more than 3 at a time! Grrr!
Also gettin new exhaust studs from work so thats a plus. Gona try to find stainless ones. "TRY!!" lol unless someone says otherwise.
Also, Oil pump doesnt seem to be leaking all that much if any.
I also made sure the EX on the piston was facing exhaust side of the jug! i read that somewhere and remembered it! Good call eh? as far as rings, thats a no brainer..Piston gots little dowel pin lookin things in it for the rings to nestle into. BRILLIANT!! lol ill get pics on ASAP!!
-Zac
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
- mustangwagz
- Elite
- Posts: 483
- Joined: Sun Mar 21, 2010 9:10 pm
- Location: Western, PA
Re: Preping for BBK...
Ok WELL, i gotta resize all my EFFIN picks..Grrrr.. lol
Anyhow, anyone got an idea on how deep the counterbore depth should be when opening head to 44mm? I got program all wrote up and waitin at work to open head, but wanna enter a Counterbore depth so i can kill 2 birds with one end mill. lol
Anyhow, anyone got an idea on how deep the counterbore depth should be when opening head to 44mm? I got program all wrote up and waitin at work to open head, but wanna enter a Counterbore depth so i can kill 2 birds with one end mill. lol
-Zac
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
- mustangwagz
- Elite
- Posts: 483
- Joined: Sun Mar 21, 2010 9:10 pm
- Location: Western, PA
Re: Preping for BBK...
here's the shmeg i found at bottom of Emo tube..
opened bystarter passage although its hard to see.. notice my stained bowl i had till i used some etching acid on it. Cleand right up after that! lol
After cleaning the entire carb and re assembling for the 7th time! lol-Zac
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
- martynkim
- Board Supporter
- Posts: 2899
- Joined: Tue Jan 05, 2010 10:22 pm
- Location: Tacoma, Washington
Re: Preping for BBK...
Yup enough shiznit to give you issues good job get that E string in the holes!
Need parts? Parting out Spree Aero and Elite!
What people share about buying from me http://www.hondaspree.net/phpBB3/viewto ... =1&t=15559
PM me with your needs Cheap Parts
What people share about buying from me http://www.hondaspree.net/phpBB3/viewto ... =1&t=15559
PM me with your needs Cheap Parts
- mustangwagz
- Elite
- Posts: 483
- Joined: Sun Mar 21, 2010 9:10 pm
- Location: Western, PA
Re: Preping for BBK...
Ok so gonna hopfully fire spree tomorrow. Aint had time to do anything yesterday or today..
As far as air filter, Should i Drill air box? (how many holes and how big?)
Also, i believe it was odin that told me to mix a little over an ounce of oil with each gallon of gas i put in ALONG WITH running stock oil pump. Sound right guys? (After break-in that is..)
I was also recommended to run the bpr8hs plug.
BBK came with a 90 jet.
its the 86 spree, with taz's 44 bbk
As far as air filter, Should i Drill air box? (how many holes and how big?)
Also, i believe it was odin that told me to mix a little over an ounce of oil with each gallon of gas i put in ALONG WITH running stock oil pump. Sound right guys? (After break-in that is..)
I was also recommended to run the bpr8hs plug.
BBK came with a 90 jet.
its the 86 spree, with taz's 44 bbk
-Zac
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
- mustangwagz
- Elite
- Posts: 483
- Joined: Sun Mar 21, 2010 9:10 pm
- Location: Western, PA
Re: Preping for BBK...
Another ?????... What kinda compression number am i shootin for? (I.E. 700 psi is to much, 10 psi is to little..)
-Zac
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
- martynkim
- Board Supporter
- Posts: 2899
- Joined: Tue Jan 05, 2010 10:22 pm
- Location: Tacoma, Washington
Re: Preping for BBK...
About 125 is stock.
Need parts? Parting out Spree Aero and Elite!
What people share about buying from me http://www.hondaspree.net/phpBB3/viewto ... =1&t=15559
PM me with your needs Cheap Parts
What people share about buying from me http://www.hondaspree.net/phpBB3/viewto ... =1&t=15559
PM me with your needs Cheap Parts
- mustangwagz
- Elite
- Posts: 483
- Joined: Sun Mar 21, 2010 9:10 pm
- Location: Western, PA
Re: Preping for BBK...
Just did the first 10 min run. Lettin it cool now. So far so good. Smoked like a bandit at first, figure thats from all the 2 stroke oil i used during assem. Also flooded itself first time. But changed plug out, and held throttle open to get MO air. took right off. So far so good guys. i got my fingers crossed. Throttle response seems WAY better already, didnt wind it out yet (not for a tank or 2 yet anyhow) so imma keep doin the warm up, cool off today and see how everything goes!!
-Zac
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
- mustangwagz
- Elite
- Posts: 483
- Joined: Sun Mar 21, 2010 9:10 pm
- Location: Western, PA
Re: Preping for BBK...
bought a 10 dollar APC filter from Advanced Auto parts. Little bit of mod with the dremel, and shave a little off the Stock Air box tube, and Tadah!! Fits like its meant to be! I gotta video of it too but gotta get it posted... Youtube i'm thinkin?
-Zac
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
- Trafficjamz
- CBR1000RR
- Posts: 5353
- Joined: Tue Jul 14, 2009 7:53 pm
- Location: Eastlake, MI
- Contact:
Re: Preping for BBK...
did you mill you own head?
Did you take a compression test?
Did you take a compression test?
new best 1/8th mile time 9.647 seconds @67.155 mph 310lbs total weight
- mustangwagz
- Elite
- Posts: 483
- Joined: Sun Mar 21, 2010 9:10 pm
- Location: Western, PA
Re: Preping for BBK...
yah, its about 123.
-Zac
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
1981 HD-Ironhead Sporty. 1000cc, 4 speed, drag pipes, and drag bars.. (chic/cop magnet)
72 Rupp Roadster 2 (aka. RUMP ROASTER!!)
05 vinson
78 bronco (Log skiddin Hog!!)
- martynkim
- Board Supporter
- Posts: 2899
- Joined: Tue Jan 05, 2010 10:22 pm
- Location: Tacoma, Washington
Re: Preping for BBK...
That rocks Zac! keep us posted.
Need parts? Parting out Spree Aero and Elite!
What people share about buying from me http://www.hondaspree.net/phpBB3/viewto ... =1&t=15559
PM me with your needs Cheap Parts
What people share about buying from me http://www.hondaspree.net/phpBB3/viewto ... =1&t=15559
PM me with your needs Cheap Parts
- Trafficjamz
- CBR1000RR
- Posts: 5353
- Joined: Tue Jul 14, 2009 7:53 pm
- Location: Eastlake, MI
- Contact:
Re: Preping for BBK...
Trafficjamz wrote:did you mill you own head?
Did you take a compression test?
How did you do your head? Dremel or Machine shop?
new best 1/8th mile time 9.647 seconds @67.155 mph 310lbs total weight