completely redid my 89 elite again (:

This is the place to post your scooter builds; everything from stock Spree restoration to water-cooled drag bikes.

Moderator: Moderator

7m-iata
Goped
Goped
Posts: 79
Joined: Sat Jul 02, 2011 11:28 pm
Location: florida
Contact:

completely redid my 89 elite again (:

Post by 7m-iata » Thu Nov 01, 2012 3:34 pm

Finally broke down and painted EVERYTHING as well as replaced the engine and reconfigured the suspension and all that jazz d:. Well here she is in all her glory I have a 1/2 gal gas tank, 73cc bore kit with "matched" pipe. All electronics and batt relocated inside the front cover 1e40qmb (minarelli/jog clone) engine. Only thing I have left to do is a little tuning and my rear lights mounted (L.E.Ds) YES it DOES have rear brakes I have the cable off right now I was debating running more of a ruckus style bar setup still havent decided yet... opinions?
Image
Image
Image
Image
Image
Image
Image
Image
Image

User avatar
deuce217
CB900F
CB900F
Posts: 1212
Joined: Thu Jun 10, 2010 4:13 am

Re: completely redid my 89 elite again (:

Post by deuce217 » Fri Nov 02, 2012 7:47 pm

Is that a chinese engine/ clone? If so I think the cover needs to be on that back to help support the clutch shaft. Or at least on my brother in laws it was needed. You might take the belt off and see how much side play there is on that shaft.

The ride looks good :thumbwink:
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)

7m-iata
Goped
Goped
Posts: 79
Joined: Sat Jul 02, 2011 11:28 pm
Location: florida
Contact:

Re: completely redid my 89 elite again (:

Post by 7m-iata » Fri Nov 02, 2012 8:10 pm

It is a chinese clone thanks for that might have to come up with an idea on that one. There isn't any play so I didn't think the bearing in the cover was all that necessary I'll look into what I can do with the case that'll still look alright.

User avatar
sum-azn-kid
Elite
Elite
Posts: 333
Joined: Mon May 24, 2010 2:04 am
Location: Hawaii, Maui

Re: completely redid my 89 elite again (:

Post by sum-azn-kid » Fri Nov 02, 2012 8:55 pm

I like the look with the panels on too bad you dont have the rear panels too.
2007 SYM DD50- baby blue 72 "Daily rider"-sold
1988 Honda SB50P-on going project
zuma 125-sold
Ninja 250r-totaled

7m-iata
Goped
Goped
Posts: 79
Joined: Sat Jul 02, 2011 11:28 pm
Location: florida
Contact:

Re: completely redid my 89 elite again (:

Post by 7m-iata » Fri Nov 02, 2012 9:16 pm

yeah I though about getting a set, but I can't find any at a price that I like since it not something I NEED more of something I WANT lol

User avatar
sum-azn-kid
Elite
Elite
Posts: 333
Joined: Mon May 24, 2010 2:04 am
Location: Hawaii, Maui

Re: completely redid my 89 elite again (:

Post by sum-azn-kid » Sat Nov 03, 2012 12:47 pm

How hard was it to swap in the jog motor? What kind of mods did you do to the wire harness?
2007 SYM DD50- baby blue 72 "Daily rider"-sold
1988 Honda SB50P-on going project
zuma 125-sold
Ninja 250r-totaled

7m-iata
Goped
Goped
Posts: 79
Joined: Sat Jul 02, 2011 11:28 pm
Location: florida
Contact:

Re: completely redid my 89 elite again (:

Post by 7m-iata » Sat Nov 03, 2012 7:06 pm

Wire harness is pretty much plug n play just match up the colors. I had to build mounts since the jog engine is top mount engine, I fabrcate for a living though it took about an hour to cut off the old mount from the frame make and weld on the tabs.

User avatar
Downsouthdio
CB900F
CB900F
Posts: 1205
Joined: Wed Dec 21, 2011 11:00 am
Location: Key west

Re: completely redid my 89 elite again (:

Post by Downsouthdio » Sat Nov 03, 2012 10:39 pm

Bro thats nice man.. Where in florida do you live..?
Honda super dio
Corsa
26mm
Sparrow

7m-iata
Goped
Goped
Posts: 79
Joined: Sat Jul 02, 2011 11:28 pm
Location: florida
Contact:

Re: completely redid my 89 elite again (:

Post by 7m-iata » Sat Nov 03, 2012 11:05 pm

I'm in sarasota its about 30 min south of tampa. Thanks it's always nice to get compliments (:

User avatar
Pismobear
Goped
Goped
Posts: 59
Joined: Fri Oct 05, 2012 6:03 pm
Location: Pismo Ca. USA

Re: completely redid my 89 elite again (:

Post by Pismobear » Mon Nov 05, 2012 6:29 pm

It looks good all layed out like that.
You gotta stop, hey, whats that sound? Everybody look.. Ah whatever.


85 Honda Aero50

User avatar
evilone
Board Supporter
Board Supporter
Posts: 3203
Joined: Sun May 18, 2008 7:26 pm
Location: Portage Michigan

Re: completely redid my 89 elite again (:

Post by evilone » Tue Nov 06, 2012 7:22 pm

Slick, nice work.
2001 Honda Elite
1995 Yamaha Jog
1994 Yamaha Axis

I can't believe
that cop put me
in the backseat
when I clearly
called shotgun.

7m-iata
Goped
Goped
Posts: 79
Joined: Sat Jul 02, 2011 11:28 pm
Location: florida
Contact:

Re: completely redid my 89 elite again (:

Post by 7m-iata » Tue Nov 20, 2012 1:50 pm

thanks, now if only it would run as good as it looks lol

Eight pack
Noob
Noob
Posts: 4
Joined: Tue Sep 25, 2012 1:43 am
Location: Stockton, CA

Re: completely redid my 89 elite again (:

Post by Eight pack » Tue Nov 20, 2012 11:51 pm

d*** that looks sick. I wanna do my spree like that now

7m-iata
Goped
Goped
Posts: 79
Joined: Sat Jul 02, 2011 11:28 pm
Location: florida
Contact:

Re: completely redid my 89 elite again (:

Post by 7m-iata » Sat Nov 24, 2012 1:54 pm

It'd be kool to see some more modded no ruckus scoots out there go for it!!

7m-iata
Goped
Goped
Posts: 79
Joined: Sat Jul 02, 2011 11:28 pm
Location: florida
Contact:

Re: completely redid my 89 elite again (:

Post by 7m-iata » Thu Dec 20, 2012 6:55 pm

Installed my lights and new wheel/tire today the lights are all wired up and blinking as they should nicely tucked under the seat (:

Image
Image

Post Reply