Sb50p sticker bomb build

This is the place to post your scooter builds; everything from stock Spree restoration to water-cooled drag bikes.

Moderator: Moderator

User avatar
benji
CB900F
CB900F
Posts: 1669
Joined: Mon Aug 10, 2015 9:15 pm
Location: renton,wa

Re: Sb50p sticker bomb build

Post by benji » Thu Nov 16, 2017 5:04 am

I have a jet drill kit, which is nice for verifying jet sizes and also redrilling jets to bigger sizes.

User avatar
Chubbyfunkmonkey
Goped
Goped
Posts: 51
Joined: Mon Nov 06, 2017 2:14 pm
Location: Seattle

Re: Sb50p sticker bomb build

Post by Chubbyfunkmonkey » Fri Nov 17, 2017 1:11 pm

I've been looking to get a good drill bit set specifically for jetting, but for now I've just been using an x-acto knife and solder. When everything is where I want I'll measure the hole and buy the jet.
1989 sb50p
2005 ruckus 50cc custom
2009 ruckus 125cc 4speed

User avatar
benji
CB900F
CB900F
Posts: 1669
Joined: Mon Aug 10, 2015 9:15 pm
Location: renton,wa

Re: Sb50p sticker bomb build

Post by benji » Fri Nov 17, 2017 7:29 pm

Look for a 'jet drill kit' it's a kit with a bunch of drill bits jet-sized. I've got one a good buddy gave me, very handy.

Here's one, kinda small tho
https://m.ebay.com/itm/New-21pc-Mini-Dr ... mwBanner=1

User avatar
Chubbyfunkmonkey
Goped
Goped
Posts: 51
Joined: Mon Nov 06, 2017 2:14 pm
Location: Seattle

Re: Sb50p sticker bomb build

Post by Chubbyfunkmonkey » Sat Nov 18, 2017 2:01 am

I've been on the look out for a nice kit but most of the ones I've seen seem kinda cheap.
1989 sb50p
2005 ruckus 50cc custom
2009 ruckus 125cc 4speed

User avatar
benji
CB900F
CB900F
Posts: 1669
Joined: Mon Aug 10, 2015 9:15 pm
Location: renton,wa

Re: Sb50p sticker bomb build

Post by benji » Sat Nov 18, 2017 11:17 am

I think alot of em are haha. But hey it is what it is. I barely use mine unless I'm tuning, then it's mostly used for checking jet sizes. Sometimes there a little off.

User avatar
Wheelman-111
Moderator
Moderator
Posts: 10913
Joined: Wed Oct 22, 2008 5:09 pm
Location: Deepinnaharta, Texas

Re: Sb50p sticker bomb build

Post by Wheelman-111 » Tue Nov 21, 2017 9:25 am

Greetings:

Here's a bigger one. The one I got had ONLY the #60 size and down - numbers inverse to the diameter. Measuring each shaft with a micro-caliper gives a fairly accurate hole size. I found clamping the drill bit and spinning the jet down onto the cutting end easier than tryin to spin the drill. The bits cut the soft brass of the jet like buttah. Shop around the HF website for several other smaller bit kits.
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
Still Seeking Red PCX-150
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox, Carb and Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 99KPH

:coolcruise:

User avatar
benji
CB900F
CB900F
Posts: 1669
Joined: Mon Aug 10, 2015 9:15 pm
Location: renton,wa

Re: Sb50p sticker bomb build

Post by benji » Tue Nov 21, 2017 12:34 pm

Image
Here's what I got. Just used it to ream out a 76 MJ to a 90 MJ, In .05 increments (75,80,85,90) worked great. Got one of the bits stuck in my finger tryna put it back in the pack tho.
Image

User avatar
Chubbyfunkmonkey
Goped
Goped
Posts: 51
Joined: Mon Nov 06, 2017 2:14 pm
Location: Seattle

Re: Sb50p sticker bomb build

Post by Chubbyfunkmonkey » Mon Dec 11, 2017 4:13 pm

Back! I was out of town for a while but I'm back in my garage finally. As for the drill bits, I caught my girlfriend snooping on the forum and I think I may be getting a new set this xmas
1989 sb50p
2005 ruckus 50cc custom
2009 ruckus 125cc 4speed

User avatar
Chubbyfunkmonkey
Goped
Goped
Posts: 51
Joined: Mon Nov 06, 2017 2:14 pm
Location: Seattle

Re: Sb50p sticker bomb build

Post by Chubbyfunkmonkey » Mon Dec 11, 2017 4:19 pm

I got home to find a dying battery. Not sure if the problem is with the battery or the charging system, but I'm headed out to get a new battery so I can find out.
1989 sb50p
2005 ruckus 50cc custom
2009 ruckus 125cc 4speed

User avatar
motormike
Moderator
Moderator
Posts: 4548
Joined: Wed Dec 29, 2010 10:58 pm
Location: Nashville, TN.

Re: Sb50p sticker bomb build

Post by motormike » Mon Dec 11, 2017 6:12 pm

Chubbyfunkmonkey wrote:I got home to find a dying battery. Not sure if the problem is with the battery or the charging system, but I'm headed out to get a new battery so I can find out.
Throwing a new battery at it will do nothing to diagnose your issue.
Instead, jump to a 12 volt source to start scooter if you must, then meter across the battery terminals to read outputs... :urban:
RideRed
OH-ARRR Racing
#53 Gyro

<Honda---Honda----Honda---Honda---Honda>
<Gyro S><XL 100><Helix><XL75><CMX450>
..Trooper....Boss......Buzby...Jon-Boy....Dolly
"If the women don't find you handsome, they should at least find you handy"

User avatar
Chubbyfunkmonkey
Goped
Goped
Posts: 51
Joined: Mon Nov 06, 2017 2:14 pm
Location: Seattle

Re: Sb50p sticker bomb build

Post by Chubbyfunkmonkey » Mon Dec 11, 2017 6:19 pm

The battery was bad. I put the new one in and gave the throttle a pull, the voltage jumped up.
1989 sb50p
2005 ruckus 50cc custom
2009 ruckus 125cc 4speed

User avatar
Chubbyfunkmonkey
Goped
Goped
Posts: 51
Joined: Mon Nov 06, 2017 2:14 pm
Location: Seattle

Re: Sb50p sticker bomb build

Post by Chubbyfunkmonkey » Mon Dec 11, 2017 6:24 pm

I'm guessing one of the cells was shorted because I was only getting 11-12 volts with the motor running before
1989 sb50p
2005 ruckus 50cc custom
2009 ruckus 125cc 4speed

User avatar
Chubbyfunkmonkey
Goped
Goped
Posts: 51
Joined: Mon Nov 06, 2017 2:14 pm
Location: Seattle

Re: Sb50p sticker bomb build

Post by Chubbyfunkmonkey » Wed Dec 13, 2017 3:28 pm

New Upgrade !

cheap and easy. all you need is a screwdriver and some stolen nail polish from your girlfriend/wife. or use your own, i won't judge

ImageIMG_1699 by chubbyfunkmonkey, on Flickr

I consider it a safety feature. now if the needle gets in to the red i know its time to wake up
1989 sb50p
2005 ruckus 50cc custom
2009 ruckus 125cc 4speed

Post Reply