SE50 build
Moderator: Moderator
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: SE50 build
project. It's a se50 (87 elite) with a 10/1 finely drive ct manifold 21 mm d slide oko carb 98 42 jets malossi head technigas silent pro 50-70cc ruckus variator with 7 gram rollers yellow Malossi spring and 3 green Polini 2k grabber springs and a 3.5 tire.... max rpm is 7800 max temp is 311 just did a compression test it was 110 useing the kick lever the books says stock is 114 to 171 max speed on the flat 35 ....
question
cood low compression be the reason for low speed???? that what i think..
swimmingfree
question
cood low compression be the reason for low speed???? that what i think..
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
- paulpauly7
- CB900F
- Posts: 1945
- Joined: Tue Feb 21, 2012 6:57 pm
- Location: nz
Re: SE50 build
drop them rollers to 3 5.5g and 3 6g rollers
86 Nifty Fifty (spree)
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
Re: SE50 build
I had 3 5g rollers and 3 6g rollers in mine pretty much the same everything else other than 9:1 gears. I hit 9k once according to the trail tech but my average was 8500-8800 at wot cruising 45 all day and topped out at 52mph. I would start with lighter rollers. I had the same problem for a bit would only go about 30-35 so I tore it down and put it back together gave the carb a good cleaning and dropped my rollers and it was much better. Last I had in my 21mm was a 105 main and 42 slow with uni filter.
86 Aero 50,Polini 65cc BBK,malossi oring head,100 oct. 32:1
21mm OKO,Malossi Wild Lion exhaust,
Stock Ruck vari, malossi special belt,1.5k shoes,1k center,
aftermarket bell, front/rear metro wheels, TT vapor,
5in stretch on motor mount,280mm Shock.
21mm OKO,Malossi Wild Lion exhaust,
Stock Ruck vari, malossi special belt,1.5k shoes,1k center,
aftermarket bell, front/rear metro wheels, TT vapor,
5in stretch on motor mount,280mm Shock.
- paulpauly7
- CB900F
- Posts: 1945
- Joined: Tue Feb 21, 2012 6:57 pm
- Location: nz
Re: SE50 build
my compression was low at 115psi last time i checked but that motor has over 2200km on it and mostly at WOT mine topped at 52mph to 54mph depending on weather .Ive actually just added some daytona rear gears bringing it to 9.5 to 1 just have to refit the motor and test them out .
86 Nifty Fifty (spree)
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: SE50 build
dam that light rollers all i have is 6 grams rollers looks like im going to get a set of rollers ...
swimmingfree
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: SE50 build
graphite9 you are a good man and a grate guy to have on this form ... A+++ seller as well ...
cant say one bad word about you
swimmingfree
cant say one bad word about you
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: SE50 build
went down the road and traded my 6 gram rollers for some 5.... put them got 8100 rpm and 30 mpr?????
so not sure what to do but put the 7s back in...
input please....
swimmingfree
so not sure what to do but put the 7s back in...
input please....
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
Re: SE50 build
Are you using the malossi kit I gave you? Those af05e dont turn real high rpms but I use to turn 9k rpm all day long on the cylinder I gave you, a keli variator, 6g rollers, that malossi yellow torque spring I gave you, 24mm carb w/ uni, unported block and unported ct manifold, and a stock modified pipe. At 110 psi it is a little low, are you opening the throttle to wide open as youre kicking it? I like to use the starter to start the compression build up then give her a couple good long swift kicks while holding it floored. Also check it after its warmed itself up.
Sounds like you have a little more carb tuning honestly. The Malossi cylinder likes to run pretty lean.
Sounds like you have a little more carb tuning honestly. The Malossi cylinder likes to run pretty lean.
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: SE50 build
yes im using the jug you gave me i do have a after marked pipe on it now its a technigas silent pro 50-70cc pipe i just put in a 100 ( was 98 ) jet and have not try it yet ... but will try later today looks like rain out ....the compression test was done cold .... im running a 21mm d slide oko carb..
thank you for the parts
swimmingfree
here some info on the pipe
https://www.google.com/url?sa=t&rct=j&q ... 1936,d.aWw
thank you for the parts
swimmingfree
here some info on the pipe
https://www.google.com/url?sa=t&rct=j&q ... 1936,d.aWw
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
Re: SE50 build
I run the silent pro for my 112cc jog clone engine. Theyre decent for all around power. Thanks for the link to that site, if I saw that first I may have re thought my decision but it takes weeks to get the jog 90 exhaust over here Ill stick it out.
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: SE50 build
dose inn body carry a honda 87 elite se50 belt????
swimmingfree
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
- Red Eft Performance
- Elite
- Posts: 449
- Joined: Sat Jun 11, 2011 10:40 am
- Location: maine
Re: SE50 build
Yes I carry Malossi Kevlar belts.swimmingfree wrote:dose inn body carry a honda 87 elite se50 belt????
swimmingfree
Keith
Red Eft Performance
To benefit forum members REP will beat the price of any legit/active Business/website
Elite, Dio, Aero, AF16/AF05 Cylinder kits,Clutches,Variators,Belts,CDI boxes,Reeds,Clutch bells,Pipes
Malossi,Polini,Fabrizi,Anything!
View products click => Here
To benefit forum members REP will beat the price of any legit/active Business/website
Elite, Dio, Aero, AF16/AF05 Cylinder kits,Clutches,Variators,Belts,CDI boxes,Reeds,Clutch bells,Pipes
Malossi,Polini,Fabrizi,Anything!
View products click => Here
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: SE50 build
wood you like to post the price for all to see???
swimmingfree
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
- Red Eft Performance
- Elite
- Posts: 449
- Joined: Sat Jun 11, 2011 10:40 am
- Location: maine
Re: SE50 build
Hello Yesswimmingfree wrote:wood you like to post the price for all to see???
swimmingfree
45$ shipped
http://www.hondaspree.net/phpBB3/viewto ... =2&t=19538
Red Eft Performance
To benefit forum members REP will beat the price of any legit/active Business/website
Elite, Dio, Aero, AF16/AF05 Cylinder kits,Clutches,Variators,Belts,CDI boxes,Reeds,Clutch bells,Pipes
Malossi,Polini,Fabrizi,Anything!
View products click => Here
To benefit forum members REP will beat the price of any legit/active Business/website
Elite, Dio, Aero, AF16/AF05 Cylinder kits,Clutches,Variators,Belts,CDI boxes,Reeds,Clutch bells,Pipes
Malossi,Polini,Fabrizi,Anything!
View products click => Here
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: SE50 build
just pull the cover off and put a tape to the belt it is 0.4375 min is 0.57... the belt has less then 900 miles on it ... dam eBay belts don't last ...
swimmingfree
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet