1994 Honda Elite S SA50 Build

This is the place to discuss your build with other builders and solicit feedback and help with parts of your build: engine, body work, bolt ons, etc.

Moderator: Moderator

Post Reply
paineisboss13
Noob
Noob
Posts: 1
Joined: Tue Jun 02, 2015 5:14 pm
Location: United states

1994 Honda Elite S SA50 Build

Post by paineisboss13 »

I'm building my '94 Honda elite s with the SA 50 motor. I want to use a 50mm bore kit i found on eBay. (http://m.ebay.com/itm/371320415883?nav=SEARCH)
What do you guys think would be the best carb and pipe I could get that won't compleatly drain my pockets.
User avatar
Rip_City_Spree
CB900F
CB900F
Posts: 1379
Joined: Sun Jun 13, 2010 7:47 pm

Re: 1994 Honda Elite S SA50 Build

Post by Rip_City_Spree »

I love my polini carb and highly recommend them. You get what you pay for spend a little more for quality parts.
01 Elite SR
polini corsa
Polini 26mm Carb
Naraku intake
Naraku sport variator
Currently 5g rollers
zx trans
Arrow
red contra with yellow clutch springs.
RIP CITY
RIP NO MERCY KERSEY
User avatar
Wheelman-111
Moderator
Moderator
Posts: 11319
Joined: Wed Oct 22, 2008 5:09 pm
Location: Deepinnaharta, Texas

Re: 1994 Honda Elite S SA50 Build

Post by Wheelman-111 »

Greetings:

Some people have good luck with Taiwanese 50mm kits. Some don't. Improve the odds with careful inspection of every inch of the cylinder. Carefully chamfer the ports to avoid having sharp edges that reportedly shave all the oil off the piston. That huge Boost Port should in theory match the size of the block's port, but remember if you cut it out that big you've doomed the block to using cylinders with similarly-sized ports. That may eliminate the excellent Polini Corsa cylinder from eligibility, which would be a shame. If you have a bore gauge and the skills to measure, see how well the piston matches the cylinder. Often these are "bin-selected" and randomly too big or too small for each other. Like I said, you could luck out, but buying Italian takes a lot of the Luck out of it. For the price difference, it's worth it to me.
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
curtis966
Elite
Elite
Posts: 833
Joined: Sat May 26, 2012 10:52 pm
Location: michigan

Re: 1994 Honda Elite S SA50 Build

Post by curtis966 »

^ All great advise. You get what you pay for.
86 Aero 50,Polini 65cc BBK,malossi oring head,100 oct. 32:1
21mm OKO,Malossi Wild Lion exhaust,
Stock Ruck vari, malossi special belt,1.5k shoes,1k center,
aftermarket bell, front/rear metro wheels, TT vapor,
5in stretch on motor mount,280mm Shock.
User avatar
Wheelman-111
Moderator
Moderator
Posts: 11319
Joined: Wed Oct 22, 2008 5:09 pm
Location: Deepinnaharta, Texas

Re: 1994 Honda Elite S SA50 Build

Post by Wheelman-111 »

Greetings:

The old scooter saying Graphie almost ( :) ) coughed up is:

Fast, Reliable, or Cheap: Pick any two. But in this case, with affordable Contesta or M'Arn kits, you can get fast and reliable FOR Cheap. My Flash 5 was a Taiwanese 50mm kit that I fussed over before bolting on, and it ran OK. Still runs, as far as I know. My experience with two other Tai 51s and a ministroker 90cc wasn't so good...
HolyPiston.jpg
HolyPiston.jpg (125.6 KiB) Viewed 4991 times
If this happens you have to split the cases, replace the bearings and start again. Now sometimes that's not so bad as it wasn't my Daily Driver and I enjoyed working on it, mostly, but you can burn out. Now it sounds like you've already bought the eBay kit, and I don't want to slag on you too much. But if you're willing to listen to advice from Those That Have Gone Before, you might consider re-selling it to the unsuspecting and switching tracks now.
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
User avatar
Xxbeejay45xx
Elite
Elite
Posts: 420
Joined: Thu Jun 19, 2014 7:13 pm
Location: Kansas

Re: 1994 Honda Elite S SA50 Build

Post by Xxbeejay45xx »

Buy Italian you will save some money in the long run. Tried and true!
95 Elite SR af16e
72cc Polini Corsa
28 Oko Carb 58/144
Ported intake
ZX Trans
Polini vari, clutch, springs
5.5 rollers
Malossi crank , CDI
Genuine Arrow pipe
Front and Rear disc brakes
Dio Live headset
Stretch and fatty rear wheel
Post Reply