Alright so I bought this scooter about a year ago and just now getting to it. It turns over but doesn't fire up. It has spark so that's not the issue. has new battery
All help is greatly
appreciated.
Link to video below
http://db.tt/mgahrFyl
I have been told to
1. plug in the nipple on the carb. that has no hose going to it.
2. clean the carb.
3. check/replace fuel filter
4. try to start it with starter fluid
anything else i should do?
Elite 80 Starting issues
Moderator: Moderator
-
- Noob
- Posts: 17
- Joined: Sun Aug 26, 2012 9:45 am
- Location: United States
Re: Elite 80 Starting issues
check compression. bad compression will keep it from starting. its usually the carb though. use carb cleaner and shoot it through all the jets.
Re: Elite 80 Starting issues
don't use starting fluid, use the fuel/oil mix you will run it. Starting fluid will not lubricate the cyl. it will actually wash any oil off the cyl and possibly cause you all sorts of grieve. Yes check compression and Clean the carb, look in the wiki for tips and proper procedure. change the plug. Good luck
taz 50mm bbk, 51g. rollers,1500 c spring
24mm arreche, #20 pilot, E2 needle clip on lower groove
arreche air filter
Naruku intake, reeds & block
v8 pipe
stock gears
trail tech temp & rpm gauges
24mm arreche, #20 pilot, E2 needle clip on lower groove
arreche air filter
Naruku intake, reeds & block
v8 pipe
stock gears
trail tech temp & rpm gauges
Re: Elite 80 Starting issues
Used the starter fluid and she fired up looks like i need to clean the carb this weekend
CH80
Re: Elite 80 Starting issues
zuphilius wrote:He has a CH80. 4 stroke.
need to read better i suppose
taz 50mm bbk, 51g. rollers,1500 c spring
24mm arreche, #20 pilot, E2 needle clip on lower groove
arreche air filter
Naruku intake, reeds & block
v8 pipe
stock gears
trail tech temp & rpm gauges
24mm arreche, #20 pilot, E2 needle clip on lower groove
arreche air filter
Naruku intake, reeds & block
v8 pipe
stock gears
trail tech temp & rpm gauges
Re: Elite 80 Starting issues
bigluelok wrote:Used the starter fluid and she fired up looks like i need to clean the carb this weekend
What is the status of the petcock ?
Is it functioning as intended with vacuum being used to open the diaphram ?
OR...has it been bypassed and is functioning as OPEN all the time ?
You say the vacuum inlet on the intake manifold was "like that" when you bought it, AND it was running then. ???????
This scooter can NOT run worth a d*mn with this inlet open.
Something seems amiss here....
RideRed
<(2)Gyro S><Helix><Sym Wolf>
"Live Large - Ride Small"
<(2)Gyro S><Helix><Sym Wolf>
"Live Large - Ride Small"
Re: Elite 80 Starting issues
haven't had chance to check out the petcock and will not have a chance till this weekend. and yes when i bought the bike it ran like that I didn't ride it but it was running and the motor revved fine.motormike wrote:bigluelok wrote:Used the starter fluid and she fired up looks like i need to clean the carb this weekend
What is the status of the petcock ?
Is it functioning as intended with vacuum being used to open the diaphram ?
OR...has it been bypassed and is functioning as OPEN all the time ?
You say the vacuum inlet on the intake manifold was "like that" when you bought it, AND it was running then. ???????
This scooter can NOT run worth a d*mn with this inlet open.
Something seems amiss here....
CH80
Re: Elite 80 Starting issues
Alright so I cleaned our the carb, and the elite starts when I spray starter fluid in to the carb but it dies after a few seconds. It will not hold idle and for some reason or another gas isn't getting to the engine any ideas. I know the jets are good as I looked through the holes and saw the sky so they aren't gunked up. Any one know what else I should check?
Also the Carb is getting fuel cuz if I open the screw on the carb bowl fuel pours out.
Also the Carb is getting fuel cuz if I open the screw on the carb bowl fuel pours out.
CH80