Page 3 of 3

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Sat Aug 07, 2010 12:45 pm
by martynkim
Wheelman-111 wrote:Greetings:

From reading here, the carb numbers vary by year but they interchange freely. The Spree carb is quite different from the Aero/Elite carb physically. The bystarter is on the opposite side of the venturi, so an Aero carb can foul the shock. Even though they might fit. I suspect the Spree carbs won't work on the Elite/Aero engines due to a very small pilot orifice - cast-in to the body.

Thanks for the answer as I am looking at the interchange of an 85 to an 87 Spree. The parts fiche from my local Honda shop shows different P/N's. I understand the differences in the variated AF motor and the non varied Spree carbs.

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Tue Aug 17, 2010 1:25 pm
by b18Eric
The flywheel from an 84 will work with the alternator coil from an 86 so no need to swap the coils/flywheel as a pair! Got pics if needed.

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Fri Jul 31, 2015 8:06 am
by Bossshelby
The spree has two different gears. the earlier is 12 tooth and the later has 13 tooth but the big gears stayed at 82 tooth for all years. The 12 tooth has a limited speed of 25mph.

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Sat Nov 07, 2015 2:25 am
by jakewright
Will 86 nq50 transmission drive gears fit in my 85 nq50 transmission case?

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Sun Dec 11, 2016 9:42 pm
by eclark5483
84/85 kickstand is shorter then 86/87 kickstand.

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Tue Aug 13, 2019 12:09 am
by chewy812
86 Honda spree Nq50


Will a 87 carburetor work on a 86 Honda spree ?

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Tue Aug 13, 2019 2:30 am
by eclark5483
yes

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Tue Aug 13, 2019 11:56 am
by chewy812
Need some help on this 86 Honda spree I put a carburetor in from a 87 Honda spree. Now I can’t keep it running I adjust the air mixture screw and nothing happens. And when I give it full throatle it dies. Any idea

I replaced the carburetor cause I put the long screw in where the short one goes will that cause a problem ?

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Tue Oct 08, 2019 6:43 pm
by Trafficjamz
Search for air leaks.
Make sure the airbox is tightly sealed.

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Thu Apr 09, 2020 7:58 pm
by Wirie01
Hi does anyone know if the rear tire of a 87 aero will fit on a 90 dio?

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Thu Apr 09, 2020 11:21 pm
by harleyracer59
yes. they both are 95mm drum brakes and shaft and spline count are the same on early dios. I think I read here at a certain year the changed the shaft diameter. I don't remember what year though. I believe variated af05 axle shafts are the same a 93-98? dio. I don't remember if its 98 or later. I have test tried an aero on both 93, & 94 af16 ive had and an af18 (year unknown). fit all of these fine

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Fri Apr 10, 2020 12:16 am
by motormike
Wirie01 wrote:
Thu Apr 09, 2020 7:58 pm
Hi does anyone know if the rear tire of a 87 aero will fit on a 90 dio?
I wonder if this poster means the WHEEL when he says TIRE ?
These kinds of questions need some further explanation.
The poster may never return, too, as it is #1 post.
:hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :hi: :coolcruise:

Re: Request for input - Parts Spree 84/85 vs 86/87 and SB50

Posted: Fri Apr 10, 2020 2:20 am
by harleyracer59
good eye mike, I didn't even pick up on the tire part. lol
hope youre good and staying healthy! take care