replaced the needle valve, still wont run..
Moderator: Moderator
-
- Spree
- Posts: 145
- Joined: Thu May 05, 2011 6:59 pm
- Location: Rome, New York
replaced the needle valve, still wont run..
ive checked the tank.. there is sediment but nothing stuck to filter, i replaced the needle, ans it still will not run, ive got spark, it runs for like 5 seconds when the throttle stop is all the way out. what??? makesd no sense.
85' Spree
Yamaha Razz
High Rev CDI
Un-Governed
Yamaha YT125 Tri-Moto
BBK
Fatboy exhaust
cool head
Yamaha Razz
High Rev CDI
Un-Governed
Yamaha YT125 Tri-Moto
BBK
Fatboy exhaust
cool head
-
- Spree
- Posts: 145
- Joined: Thu May 05, 2011 6:59 pm
- Location: Rome, New York
Re: replaced the needle valve, still wont run..
and throttle causes it to die right away.. wont even start when the throttle is pulled back
85' Spree
Yamaha Razz
High Rev CDI
Un-Governed
Yamaha YT125 Tri-Moto
BBK
Fatboy exhaust
cool head
Yamaha Razz
High Rev CDI
Un-Governed
Yamaha YT125 Tri-Moto
BBK
Fatboy exhaust
cool head
Re: replaced the needle valve, still wont run..
Hello: I know it's no fun, but clean the carb. again. follow the instructions in the wiki spreedia on this forum. no one likes to clean the carb several times but seems to be a constant with these things. also check the torgue and gaskets of the complete intake. orings, reed gaskets. Lately ive had my carb apart numerous times and still unable to find my particular problem. good luck
taz 50mm bbk, 51g. rollers,1500 c spring
24mm arreche, #20 pilot, E2 needle clip on lower groove
arreche air filter
Naruku intake, reeds & block
v8 pipe
stock gears
trail tech temp & rpm gauges
24mm arreche, #20 pilot, E2 needle clip on lower groove
arreche air filter
Naruku intake, reeds & block
v8 pipe
stock gears
trail tech temp & rpm gauges
- Wheelman-111
- Moderator
- Posts: 11325
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: replaced the needle valve, still wont run..
Greetings:
Your problem sounds like a Classic Case o' Carb Crud. Remove, dismantle and thoroughly clean that carb, again. Search for and find the Tiny Pin-* O' Light. Don't reinstall until you have Seen tha' Light. Great God a'Mighty!! Ah have see-yun (rhymes with green...) tha' Light!!
Your problem sounds like a Classic Case o' Carb Crud. Remove, dismantle and thoroughly clean that carb, again. Search for and find the Tiny Pin-* O' Light. Don't reinstall until you have Seen tha' Light. Great God a'Mighty!! Ah have see-yun (rhymes with green...) tha' Light!!
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
-
- Spree
- Posts: 145
- Joined: Thu May 05, 2011 6:59 pm
- Location: Rome, New York
Re: replaced the needle valve, still wont run..
carb has nbeen cleaned like 40 times by now.
85' Spree
Yamaha Razz
High Rev CDI
Un-Governed
Yamaha YT125 Tri-Moto
BBK
Fatboy exhaust
cool head
Yamaha Razz
High Rev CDI
Un-Governed
Yamaha YT125 Tri-Moto
BBK
Fatboy exhaust
cool head
Re: replaced the needle valve, still wont run..
Cleaned, but not cleaned properly to fix the problem.frenchiehxc wrote:carb has nbeen cleaned like 40 times by now.
Did you do this when you replaced the needle?
http://hondaspree.net/wiki/index.php5?t ... Valve_Seat
If the seat is bad a new needle will fix nothing, as you found out.
Is the float bad?
Bear 45/70
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
-
- Spree
- Posts: 145
- Joined: Thu May 05, 2011 6:59 pm
- Location: Rome, New York
Re: replaced the needle valve, still wont run..
floats good.. the seat isnt replaceable. its solid in the carb. but i cleaned the livin s*** out of it, turns out the needle i ordered was bad. took to the shop they had me send ir back. new one will be here in 5 das.
85' Spree
Yamaha Razz
High Rev CDI
Un-Governed
Yamaha YT125 Tri-Moto
BBK
Fatboy exhaust
cool head
Yamaha Razz
High Rev CDI
Un-Governed
Yamaha YT125 Tri-Moto
BBK
Fatboy exhaust
cool head
-
- Spree
- Posts: 145
- Joined: Thu May 05, 2011 6:59 pm
- Location: Rome, New York
Re: replaced the needle valve, still wont run..
new needle still didnt fix it
85' Spree
Yamaha Razz
High Rev CDI
Un-Governed
Yamaha YT125 Tri-Moto
BBK
Fatboy exhaust
cool head
Yamaha Razz
High Rev CDI
Un-Governed
Yamaha YT125 Tri-Moto
BBK
Fatboy exhaust
cool head