Help fixing scorpion pipe
Moderator: Moderator
- kingkamehameha
- CB900F
- Posts: 1215
- Joined: Sat Apr 16, 2011 1:11 pm
- Location: kailua kona
Help fixing scorpion pipe
Need some ideas in how to fix this
ua mau ke 'ea o ka aina i ka pono o hawaii
- Dio89Elite
- Elite
- Posts: 701
- Joined: Wed Feb 01, 2012 3:55 pm
- Location: 50th state
Re: Help fixing scorpion pipe
cut that broken tab down a little bit,
leaving the bottom part that's connected to the pipe,
construct a replacement piece (size it up and predrill)
and weld it to the part that you left on (and/or the pipe).
leaving the bottom part that's connected to the pipe,
construct a replacement piece (size it up and predrill)
and weld it to the part that you left on (and/or the pipe).
Last edited by Dio89Elite on Thu Mar 01, 2012 4:18 am, edited 1 time in total.
- paulpauly7
- CB900F
- Posts: 1945
- Joined: Tue Feb 21, 2012 6:57 pm
- Location: nz
Re: Help fixing scorpion pipe
If you dont have access to a welder do the same as above but bolt it to whats left on the pipe
86 Nifty Fifty (spree)
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
-
- Elite
- Posts: 314
- Joined: Thu Feb 24, 2011 11:09 am
- Location: Broken Arrow, OK
Re: Help fixing scorpion pipe
Send it to me and ill fix it.
- SuprasNsprees
- Elite
- Posts: 564
- Joined: Mon Jun 20, 2011 2:05 pm
- Location: saint louis
- Contact:
Re: Help fixing scorpion pipe
Extremely basic fabrication
'86 Honda Spree : taz stage3 w/ mild porting, head milled 0.015", and pulley mod. 2k+ mies on kit
'80 Puch Magnum MKII
'78 Maxi Newport. Polini 64cc case matched, hi comp head, Rito alum crank, delorto 21mm race, etc.
'78 PA50 Hobbit
'80 Puch Magnum MKII
'78 Maxi Newport. Polini 64cc case matched, hi comp head, Rito alum crank, delorto 21mm race, etc.
'78 PA50 Hobbit
-
- CBR1000RR
- Posts: 4219
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: Help fixing scorpion pipe
Keep a fire extinguisher handy. 2t pipes tend to have flammable left overs inside.
motormike wrote:Errands become adventures.
- kingkamehameha
- CB900F
- Posts: 1215
- Joined: Sat Apr 16, 2011 1:11 pm
- Location: kailua kona
Re: Help fixing scorpion pipe
Not really. The angle of the plate has to be perfect
ua mau ke 'ea o ka aina i ka pono o hawaii
-
- CBR1000RR
- Posts: 4219
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: Help fixing scorpion pipe
The angle is already there. Just make a template for the hole. Mock up and weld. If you don't want to weld, rivet another plate there. If you change your mind, you just drill the rivets and patch the holes.
motormike wrote:Errands become adventures.
- SuprasNsprees
- Elite
- Posts: 564
- Joined: Mon Jun 20, 2011 2:05 pm
- Location: saint louis
- Contact:
Re: Help fixing scorpion pipe
no, really.
'86 Honda Spree : taz stage3 w/ mild porting, head milled 0.015", and pulley mod. 2k+ mies on kit
'80 Puch Magnum MKII
'78 Maxi Newport. Polini 64cc case matched, hi comp head, Rito alum crank, delorto 21mm race, etc.
'78 PA50 Hobbit
'80 Puch Magnum MKII
'78 Maxi Newport. Polini 64cc case matched, hi comp head, Rito alum crank, delorto 21mm race, etc.
'78 PA50 Hobbit
- kingkamehameha
- CB900F
- Posts: 1215
- Joined: Sat Apr 16, 2011 1:11 pm
- Location: kailua kona
Re: Help fixing scorpion pipe
Your not helpfull supra why dont you just stay off my threads. You just post nonsenseSuprasNsprees wrote:no, really.
ua mau ke 'ea o ka aina i ka pono o hawaii
- paulpauly7
- CB900F
- Posts: 1945
- Joined: Tue Feb 21, 2012 6:57 pm
- Location: nz
Re: Help fixing scorpion pipe
If you use rivits use stainless steel ones if you use alloy ones they will work there way loose and that could be the end of your pipe or jug i would use bolts
86 Nifty Fifty (spree)
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
Re: Help fixing scorpion pipe
If you don't have a welder or know someone that can do it for you,use anut and bolts to hold the plate to the exhaust mount. Rivots will come loose from vibration. 1/8th inch steel plate should be fine. Home depot or lowes got them in short strips about 2in wide or 3in wide ones
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: Help fixing scorpion pipe
to get all to line up you need to bolt the pipe on the motor and the peace you made then give it a jue good tacks an both sides let it cool down in place on the motor.. then a fue more tacks on both side ... tack it off the bike and weld it up good .. the better the tack the less it will warp out of shape ..
swimmingfree
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
- kingkamehameha
- CB900F
- Posts: 1215
- Joined: Sat Apr 16, 2011 1:11 pm
- Location: kailua kona
Re: Help fixing scorpion pipe
Sweet im gonna make a cardboard stencil piece and go buy some sheet metal. Thanks guys
ua mau ke 'ea o ka aina i ka pono o hawaii
Re: Help fixing scorpion pipe
By any chance,do you still have the broken off piece?That would go a long way to making the template.If not bolt the pipe up in position,carefully brace it up as not to break off the mounting studs.Then you can get a good questamation of the needed dimensions.Then cut a template out of cardboard/paperboard,tape it in place,and see how close.Repeat till it's lookin good.If you know someone that can/will weld it,cool.Remember to bring the welder a "couple of sodas".If not you could drill and bolt(small bolts)it up into place till you can get it welded.That might be a good way to test out the fit.I hope this made some sense.Good luck.Carp
'98 sa50(thanks evailone),'95 sa 50,'86 spree(thanks wikked_spree57) ,'82 nu,'81 puch,'80 nc,(2)'78nc
'78 ranchero,'77 pinto wagon,'64 t bird,'48 ford tudor,'31 ford furdor
and they all need lots of love !!!
'78 ranchero,'77 pinto wagon,'64 t bird,'48 ford tudor,'31 ford furdor
and they all need lots of love !!!