Rusty dio wheels

Trying to get your Spree/Elite to run, or run better? Post your questions here.

Moderator: Moderator

Post Reply
Hksdio
Spree
Spree
Posts: 130
Joined: Sat Dec 05, 2015 9:37 pm
Location: Australia

Rusty dio wheels

Post by Hksdio »

Hi all,

Second week with this dio and my shocks and seat are avout to arrive from japan. This weekend i would like to refurbish the wheels.

I plan to have the tyres removed and get the bulk of the rust off with a wire wheel, then sand prime paint and clear.

This is the condition of the wheels, if anyone has any advice or experience and if possible a way i could do this without removing the tyres it would be great.

Image

Thanks in advance!
User avatar
kuromi
Spree
Spree
Posts: 158
Joined: Fri Jul 03, 2015 4:21 am
Location: Manchester, England

Re: Rusty dio wheels

Post by kuromi »

You'll get a better result with the tyres off and it's fairly easy to remove them with tyre irons.
Make sure you protect the rim when you lever them off.

If you really don't want to take the tyres off, I guess you could deflate the tyres then put masking tape and newspaper around the tyre.

If you're using rattle cans you can get 2 pack clear coat which gives a harder finish to the wheels, though you should use an air fed mask with it (poisonous) and you get about an hour to use it before it goes hard in the can.
1983 Melody Deluxe II / ND50MC
1984 Melody Mini / NP50D
1979 Simson Schwalbe KR51/1 (think 2 wheel trabant/ East German Honda Cub)
Johnniespeed
Elite
Elite
Posts: 316
Joined: Sat Nov 17, 2012 8:18 pm
Location: Sunny Surburbon Sparta Michigan

Re: Rusty dio wheels

Post by Johnniespeed »

I don't think you will be happy with the wire wheel results.
I strongly suggest to sandblast them, that is the only way to get your primer or powder to adhere.
If you sandblast them you have the option of prime/color/clear, or powdercoating.
I usually sandblast them myself, frequently I am in too much of a rush for powder, ( even though a friend owns a powdercoat shop) so I prime them and then use a semi-flat silver, also known as Argent silver.
You don't have to remove the tires from the wheels, but it only takes a few minutes, I use a bench vise to break the beads, and a couple tire spoons to flip the tire off.
1984 Aero 125 57 mph for sale.

Elite 150 64 mph for sale.

Elite 250 77 mph. for sale.

Red Honda Grom, modded to 250cc, 87 mph.

GSXR 1000 168 mph. My new favorite, scooters seems way too slow now.
User avatar
deuce217
CB900F
CB900F
Posts: 1212
Joined: Thu Jun 10, 2010 4:13 am

Re: Rusty dio wheels

Post by deuce217 »

I also would sand blast. Rust is sneaky and will come back. Blasting does a wonderful job. Your wheels will look new after.
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
Hksdio
Spree
Spree
Posts: 130
Joined: Sat Dec 05, 2015 9:37 pm
Location: Australia

Re: Rusty dio wheels

Post by Hksdio »

Update. I did the wire wheel and white paint. Eventually i will grab a used pair and have them sandblasted because im ocd.
Image
User avatar
deuce217
CB900F
CB900F
Posts: 1212
Joined: Thu Jun 10, 2010 4:13 am

Re: Rusty dio wheels

Post by deuce217 »

They look good. Way better!
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
Post Reply