Does your Spree/Elite already run great, and you're trying to make it quicker/faster? Need a monster motor swap? Discuss your ideas here.
Moderator: Moderator
killingspree
BMX
Posts: 24 Joined: Sun May 14, 2006 3:03 pm
Location: rochester ny
Post
by killingspree » Wed May 17, 2006 6:13 pm
where can i order a pipe for my 84 spree, and pully weights, and anything else that will make it faster....
scoot2er
BMX
Posts: 33 Joined: Sat May 13, 2006 11:21 am
Location: Sacramento California
Post
by scoot2er » Wed May 17, 2006 6:55 pm
Sorry, no tortilla. No such thing as an aftermarket spree pipe. Though you can fabricate one. Cruise on thru this here forum when u get the time.
What it is?
killingspree
BMX
Posts: 24 Joined: Sun May 14, 2006 3:03 pm
Location: rochester ny
Post
by killingspree » Wed May 17, 2006 9:11 pm
dude thats what they call me at work " big Al " how did you know ? anything else i can do, isnt there weights for the cluts or som,ething you can get ?
killingspree
BMX
Posts: 24 Joined: Sun May 14, 2006 3:03 pm
Location: rochester ny
Post
by killingspree » Wed May 17, 2006 9:38 pm
well i stopped being lazy and looked in the tech docs............
-aL-
Elite
Posts: 519 Joined: Mon Jul 23, 1973 10:24 am
Location: Escanaba, MI
Post
by -aL- » Wed May 17, 2006 9:38 pm
people call me al too... s***...
Ridin' Dirty on one of my 1989 Honda Elite E's
scoot2er
BMX
Posts: 33 Joined: Sat May 13, 2006 11:21 am
Location: Sacramento California
Post
by scoot2er » Wed May 17, 2006 11:45 pm
I keep mine stock, likes to drive it to work. Cal gas prices 3.23/ gallon where im at.
What it is?
darat
Veteran OG
Posts: 3133 Joined: Fri Jul 23, 2004 10:24 am
Location: Fraser Michigan
Contact:
Post
by darat » Thu May 18, 2006 9:50 am
well noiseguy is makeing them so u should buy one off of him.
MICHIGAN MOPED MAFIA Co Founder VET OG. 95 YAMAHA JOG 70CC
mopedman
CB900F
Posts: 1214 Joined: Mon Jul 23, 1973 10:24 am
Location: sterling Heights MI
Contact:
Post
by mopedman » Thu May 18, 2006 9:56 am
buy one from noiseguy
Michigan Moped Mafia founding member
2005 Yamaha Zuma
1985 Honda Spree
1978 Honda Express
killingspree
BMX
Posts: 24 Joined: Sun May 14, 2006 3:03 pm
Location: rochester ny
Post
by killingspree » Thu May 18, 2006 10:14 am
nah i can make my own, buuuuttt i was reading the docs and i prolly didnt look hard enough but the pully mod, you just grind out the spacing on the front pully, i thought there was a mod with weights for the cintrifical clutch... i dont know if i spelt that right but i dont care
mopedman
CB900F
Posts: 1214 Joined: Mon Jul 23, 1973 10:24 am
Location: sterling Heights MI
Contact:
Post
by mopedman » Thu May 18, 2006 10:16 am
there is, but it is not for a spree, it is for elites
Michigan Moped Mafia founding member
2005 Yamaha Zuma
1985 Honda Spree
1978 Honda Express
noiseguy
Site Admin
Posts: 4419 Joined: Sat Jul 31, 2004 8:00 pm
Location: South Florida
Contact:
Post
by noiseguy » Thu May 18, 2006 10:47 am
If you build your own pipe make sure to match up the length of the downtube on the Spree to the downtube of the donor pipe. Otherwise they don't work well.
scoot2er
BMX
Posts: 33 Joined: Sat May 13, 2006 11:21 am
Location: Sacramento California
Post
by scoot2er » Thu May 18, 2006 5:12 pm
you guys notice how a muffler mod always takes a topical turn into a pulley mod? I did the same thing.
What it is?
darat
Veteran OG
Posts: 3133 Joined: Fri Jul 23, 2004 10:24 am
Location: Fraser Michigan
Contact:
Post
by darat » Thu May 18, 2006 5:29 pm
yea
MICHIGAN MOPED MAFIA Co Founder VET OG. 95 YAMAHA JOG 70CC
noiseguy
Site Admin
Posts: 4419 Joined: Sat Jul 31, 2004 8:00 pm
Location: South Florida
Contact:
Post
by noiseguy » Fri May 19, 2006 12:39 am
Lots of ppl mess with weights/ramps, very few purchase (and fewer build) their own pipes.