pg long swaped
Moderator: Moderator
pg long swaped
I installed my pg long last night and have been cruising all day long. The scooter does not rev as high as it used to. Im running a 24mm carb with a 120 jet middle clip and 6 gram weights in the vari. I also have no low end take off until i go wot. Where should I start.
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: pg long swaped
You have to rejet when you change pipes.
Bear 45/70
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
- Wheelman-111
- Moderator
- Posts: 11321
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: pg long swaped
Greetings:
Is the PG new or used?
The Bear is correct, but 120 may be close. Also the Pilot size matters. Which Pilot is in your 24?
Is the PG new or used?
The Bear is correct, but 120 may be close. Also the Pilot size matters. Which Pilot is in your 24?
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Re: pg long swaped
What bore kit are you running? (brand/ cc?)
What type of air filter?
What clutch springs are you running? (both center and clutch shoe springs)
With the use of a PG Long pipe, these are ideal OKO 24mm carb settings:
Main: 125
Pilot: 50
Air screw: 1-1/2 turns "out"
Throttle needle setting: Middle groove
These settings work well with a UNI 2stage air filter.
~Patrick
What type of air filter?
What clutch springs are you running? (both center and clutch shoe springs)
With the use of a PG Long pipe, these are ideal OKO 24mm carb settings:
Main: 125
Pilot: 50
Air screw: 1-1/2 turns "out"
Throttle needle setting: Middle groove
These settings work well with a UNI 2stage air filter.
~Patrick
Last edited by S4Patrick on Fri Jun 22, 2012 5:16 pm, edited 1 time in total.
'87 Aero 50 STOCK (only 350miles)
'87 Aero (AF16 Corsa-PG-Short-OKO24mm-8.44)
'86 Aero (AF16 Corsa-SEF Black-OKO21mm-8.44)
'98 Live Dio ZX - 50th Anniversary Edition 68cc
'92 Super Dio ZX - AF18 Corsa
Visit: http://www.airtoolsforless.com
'87 Aero (AF16 Corsa-PG-Short-OKO24mm-8.44)
'86 Aero (AF16 Corsa-SEF Black-OKO21mm-8.44)
'98 Live Dio ZX - 50th Anniversary Edition 68cc
'92 Super Dio ZX - AF18 Corsa
Visit: http://www.airtoolsforless.com
Re: pg long swaped
I have an mhr hyper racing kit. 72cc with a ct mani. im running a 48 pilot 1-3/4 turns out on mixture screw. Im running 6/6.2 gram weights.
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: pg long swaped
Alright, good stuff there....
Your contra/ rear clutch spring rating is?
Your contra/ rear clutch spring rating is?
'87 Aero 50 STOCK (only 350miles)
'87 Aero (AF16 Corsa-PG-Short-OKO24mm-8.44)
'86 Aero (AF16 Corsa-SEF Black-OKO21mm-8.44)
'98 Live Dio ZX - 50th Anniversary Edition 68cc
'92 Super Dio ZX - AF18 Corsa
Visit: http://www.airtoolsforless.com
'87 Aero (AF16 Corsa-PG-Short-OKO24mm-8.44)
'86 Aero (AF16 Corsa-SEF Black-OKO21mm-8.44)
'98 Live Dio ZX - 50th Anniversary Edition 68cc
'92 Super Dio ZX - AF18 Corsa
Visit: http://www.airtoolsforless.com
Re: pg long swaped
Transmission....... Polini rukus vari, pg driveface, cut kick cover electric start only. I have stock clutch ramps(Brand new) Polini clutch pads red spring on the pads and a 2k center spring. 8.2 rear end. 90/90 tires
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: pg long swaped
Transmission....... Polini rukus vari, pg driveface, cut kick cover electric start only. I have stock clutch ramps(Brand new) Polini clutch pads red spring on the pads and a 2k center spring. 8.2 rear end. 90/90 tires. Clutch grabs at 4100 rpms and i max out around 9300rpm. temp runs under 310f at wot never gone past 323f. If i ride at 2/3 throttle itll run like my r6 but anywhere else its just not moving at all.
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: pg long swaped
So i was playing with jets and i got it all the way up to 130 on the center clip. It would run but gargle at every position but wot. I went to change my plug and check found out its been sitting crooked. ill be tapping it in the morning. No matter what size jet i install it still gargles. Can too light of weights effect this? Im open to suggestion.
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: pg long swaped
WOT is controlled by the main jet size. Anything from 1/4 to 3/4 that is controlled by the needle. So adjust it after doing a plug chop where the engine is gargling, whatever that is.TikiMan wrote:So i was playing with jets and i got it all the way up to 130 on the center clip. It would run but gargle at every position but wot. I went to change my plug and check found out its been sitting crooked. ill be tapping it in the morning. No matter what size jet i install it still gargles. Can too light of weights effect this? Im open to suggestion.
Bear 45/70
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree