questions about SE50 Spree swap
Moderator: Moderator
questions about SE50 Spree swap
Swapping an 87' SE50 Elite motor into my Spree. Wondering about these parts compatibility: Rectifier, CDI, ignition coil/wire,...are all these on my spree OK to use with the SE50 motor? Any other wiring that needs to be changed/modified? I'm sure I will ask many more questions during this process. Thx.
I need to find some new haters...the ones I have are starting to like me.
Re: questions about SE50 Spree swap
When doing the SE50 to Spree swap, How are you guys handling the wires going to the stator? Are you guys pulling the flywheel and actually unplugging the wires or leaving it all attached and cutting/splicing the wires to the Spree? Same question with Rectifier, CDI, Starter etc.
I need to find some new haters...the ones I have are starting to like me.
Re: questions about SE50 Spree swap
So Ive got the SE50 motor onto the Spree and the back wheel rubs against the plastic fender. How have you guys been solving this? I used the shock from the SE50 since the Spree shock is shorter which would make it worse. Any suggestions?
- Attachments
-
- wheel rub.JPG (88.89 KiB) Viewed 9167 times
I need to find some new haters...the ones I have are starting to like me.
Re: questions about SE50 Spree swap
I relocated the shock mount higher up on the frame. It raised the scoot up a lil bit and made the rubbing a bit less but still rubs. It also leveled out the carb a bit since it was sitting an angle. Thanks for all your input on this swap, guys.
I need to find some new haters...the ones I have are starting to like me.
Re: questions about SE50 Spree swap
Variator shot
- Attachments
-
- variator.JPG (84.99 KiB) Viewed 9158 times
I need to find some new haters...the ones I have are starting to like me.
Re: questions about SE50 Spree swap
Forgive my ignorance Meatball, is that the variated AF05E motor?
I know the AF16/18 engine wiring is compatible with the Spree harness by just matching and joining up the colours
Maybe just buy some male/female bullet connectors, cut the plugs, crimp up and away you go
I know the AF16/18 engine wiring is compatible with the Spree harness by just matching and joining up the colours
Maybe just buy some male/female bullet connectors, cut the plugs, crimp up and away you go
Re: questions about SE50 Spree swap
You are correct. I swapped a SE50 Elite motor(AF05e variated)into my Spree. As for the wiring, that's exactly what I did. I used "female butt" connectors and it worked out great. All the wire colors were the same which made it a snap. My next problem is figuring out a Kickstand. Anyone have ideas?
I need to find some new haters...the ones I have are starting to like me.
Re: questions about SE50 Spree swap
I use whatever is close... I don't have one and I just lean it up against stuff like walls usually
Re: questions about SE50 Spree swap
Check out the the wiki on side kickstands !! They use clamps and a cheap kick stand off of a chinese scooter.
Meatball did the engine just bolt on??
Meatball did the engine just bolt on??
Re: questions about SE50 Spree swap
My MLM pipe came in today for my spree and man what a diffrence. Its stock and sounds like a 2 stroke dirtbike
Re: questions about SE50 Spree swap
Did you notice any performance improvements with the MLM or just a cool noise?
I need to find some new haters...the ones I have are starting to like me.
Re: questions about SE50 Spree swap
Big performance man. I should.shoot a video sometime and show you. Lost a little.bottom end but I'm doing 35 and shredding.hills. I love it
-
- Elite
- Posts: 392
- Joined: Mon Feb 01, 2016 11:04 pm
- Location: beaverton, or
Re: questions about SE50 Spree swap
I put a side stand on my dio so i have a stock center stand that'll work for that. Pm if u want it.
2000 Honda SR (purple swurp)
corsa
naruku
polini 21 cp 36/106 pod filter
polini vari 5.5 gram
zx trans
Polini evo2 clutch/bell yellow springs (slacked) yellow contra
Yasuni C16
stock crank/gears=wheelie machine
70 mph/12,470 rpm Trail tech vapor verified
corsa
naruku
polini 21 cp 36/106 pod filter
polini vari 5.5 gram
zx trans
Polini evo2 clutch/bell yellow springs (slacked) yellow contra
Yasuni C16
stock crank/gears=wheelie machine
70 mph/12,470 rpm Trail tech vapor verified
Re: questions about SE50 Spree swap
Im not sure how a center stand will mount to my set-up. The mount where the kickstand used to be is now blocked by the SE50 motor mount. See pic.Meloshameless wrote:I put a side stand on my dio so i have a stock center stand that'll work for that. Pm if u want it.
- Attachments
-
- kickstand mount.JPG (92.2 KiB) Viewed 9074 times
I need to find some new haters...the ones I have are starting to like me.
-
- Elite
- Posts: 392
- Joined: Mon Feb 01, 2016 11:04 pm
- Location: beaverton, or
Re: questions about SE50 Spree swap
I see ur predicament. I found a motorcycle shop with used parts and bought a kick stand from some type of harley that came with a spring and bolted it to my frame.
2000 Honda SR (purple swurp)
corsa
naruku
polini 21 cp 36/106 pod filter
polini vari 5.5 gram
zx trans
Polini evo2 clutch/bell yellow springs (slacked) yellow contra
Yasuni C16
stock crank/gears=wheelie machine
70 mph/12,470 rpm Trail tech vapor verified
corsa
naruku
polini 21 cp 36/106 pod filter
polini vari 5.5 gram
zx trans
Polini evo2 clutch/bell yellow springs (slacked) yellow contra
Yasuni C16
stock crank/gears=wheelie machine
70 mph/12,470 rpm Trail tech vapor verified