AF16E not quite right
Moderator: Moderator
AF16E not quite right
Hello,
My 87se is only topping out around 48mph about 2 weeks ago I had a run at 52mph. what would cause a change in 4mph and is there a way to get me cruising a little bit faster.
Im running a 2001 AF16E with a malossi 72cc cast iron kit, intake and 24mm oko carb 135main 52 pilot. Pg short pipe(switching to long once it arrives) and a polini rukus vari with 7 and 8 gram weights with a 9.44 rear end. Its running amazing and I don't have many complaints with the 500 miles I've on it since break in.
My 87se is only topping out around 48mph about 2 weeks ago I had a run at 52mph. what would cause a change in 4mph and is there a way to get me cruising a little bit faster.
Im running a 2001 AF16E with a malossi 72cc cast iron kit, intake and 24mm oko carb 135main 52 pilot. Pg short pipe(switching to long once it arrives) and a polini rukus vari with 7 and 8 gram weights with a 9.44 rear end. Its running amazing and I don't have many complaints with the 500 miles I've on it since break in.
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: AF16E not quite right
mark the variator face with a sharpie and see how high the belt is going. does the engine rpm drop some as your getting into topend speed?
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Re: AF16E not quite right
Ill take a pic tomorrow after a couple of runs
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: AF16E not quite right
This is my pic of pre test run with 7's in the vari. I will be trying to do a run tomorrow if its not wet out or raining. But what do ya think im getting the belt fairly high.
- Attachments
-
- 2012-04-25_16-21-29_98 (800x598) (500x374).jpg (128.11 KiB) Viewed 5169 times
-
- 2012-04-25_16-19-40_402 (800x598) (500x367).jpg (116.5 KiB) Viewed 5169 times
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: AF16E not quite right
weather change ill make the bike run different too. air temp, humdity berometric pressure, that all will effect how a 2 stroke motor runs. these motors are sensitive to changes
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Re: AF16E not quite right
I feel like that is not a great top speed. Try a tach and see what your powerband looks like. Phongeer might like more revs. Try to check your tire pressure could be the issue
Re: AF16E not quite right
So yesterday i did some runs with different weights to see what eould happen. Nomatter what weihts i installed it would not go over 49mph. Im starting to lean towards changing the gears. I believe 8.44 would be a first good try and maywbr something lower just incase. Any ideas?
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: AF16E not quite right
does your carb have a hose that goes from the bowl to the top of the mouth of the carb? plus the jets your using is more for a 28mm carb so you might over jetted too. at wot it will 4 stroke and cause the bike to not rev up as high as it should.TikiMan wrote:So yesterday i did some runs with different weights to see what eould happen. Nomatter what weihts i installed it would not go over 49mph. Im starting to lean towards changing the gears. I believe 8.44 would be a first good try and maywbr something lower just incase. Any ideas?
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
-
- CBR1000RR
- Posts: 4219
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: AF16E not quite right
Sounds like a problem solver. 9.44 is a ratio I would use on a stock bore. 8.44 to 9.0 would be a better set for breaking 50mph and keeping quicker acceleration.TikiMan wrote:So yesterday i did some runs with different weights to see what eould happen. Nomatter what weihts i installed it would not go over 49mph. Im starting to lean towards changing the gears. I believe 8.44 would be a first good try and maywbr something lower just incase. Any ideas?
motormike wrote:Errands become adventures.
Re: AF16E not quite right
When i had my Malossi setup and 28mm carb i ran 55 pilot and 138 main, i overlooked you are running a 24mm
2001 Honda Elite
1995 Yamaha Jog
1994 Yamaha Axis
I can't believe
that cop put me
in the backseat
when I clearly
called shotgun.
1995 Yamaha Jog
1994 Yamaha Axis
I can't believe
that cop put me
in the backseat
when I clearly
called shotgun.
Re: AF16E not quite right
it can faser than that with the parts he is using. with a stock exhaust yeah 50-55mph can be done with those gears. he is using a pg short and even if a pg long was being used, they both rev into the 10300rpm range which should get past 49mph for sure. sounds more like a carb issue going on thats holding him back or possible leak somewhere thats having him jet so big for that size carb.eliteguy50 wrote:Sounds like a problem solver. 9.44 is a ratio I would use on a stock bore. 8.44 to 9.0 would be a better set for breaking 50mph and keeping quicker acceleration.TikiMan wrote:So yesterday i did some runs with different weights to see what eould happen. Nomatter what weihts i installed it would not go over 49mph. Im starting to lean towards changing the gears. I believe 8.44 would be a first good try and maywbr something lower just incase. Any ideas?
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Re: AF16E not quite right
Update!!!!!!! Did a different run the other day a lil big longer stretch right next to the river with some nice turns and wow. Hit 52mph at 9890.q
- Attachments
-
- 2012-05-01_20-55-41_68 (250x187).jpg (53.94 KiB) Viewed 5023 times
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: AF16E not quite right
so for sure your using a 24mm oko carb with 135 main and 52 pilot jet in it?
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Re: AF16E not quite right
For sure ill snap some pics with the micrometer and make sure. But i know from the receipt its a 24mm. Give me a bit to get it on the lift and apart ill confirm.
88 SA 50- Af16e swap
87 Se 50 - 01 Af16E build
87 Se 50 - 01 Af16E build
Re: AF16E not quite right
if its a oko 24mm carb it will say right there on the side 24mm stamped on it. check the exhaust for leak under the flange. thats a common place for the pg pipes to leak.also check the vacuum hose to the mani and the nipple for the vacuum hose. if the hose is not really snugg,it will suck air in. the nipple on the ct manis are prone to leak too. I jb weld those nipples in. those jets are really big if your carb is a 24mm carb.TikiMan wrote:For sure ill snap some pics with the micrometer and make sure. But i know from the receipt its a 24mm. Give me a bit to get it on the lift and apart ill confirm.
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r