NQ50 build , nothing to lose , heaps to gain
Moderator: Moderator
Re: NQ50 build , nothing to lose , heaps to gain
I said it before, I will say it again. Your fiber skillz are a whole lot of fun to see!!!
Re: NQ50 build , nothing to lose , heaps to gain
The worship goes both ways.Fishman43 wrote:
I said it before, I will say it again. Your fiber skillz are a whole lot of fun to see!!!
, you made some top notch petcock covers
They looked really OEM.
I still have a lot to learn, But I think my skills have gotten better, If I were to do some of it again I think the results would be better too, Im learning how to manipulate the fibres and how to work with the resin better, as per any hand craft with extra experience
-
- Veteran OG
- Posts: 3639
- Joined: Tue May 22, 2007 8:10 pm
- Location: North of Seattle, WA
Re: NQ50 build , nothing to lose , heaps to gain
Yes, you could build a signal generator like that. Put a counter on it is a good idea. I agree, square wave only. Post some pics if you build this!that hertz generator sounds like a good idea, but I would not know where to begin.
is this sort of what I would be after? http://www.overunity.com/6857/diy-simpl ... generator/
I guess I could simplify this a lot by making it only 1 wave and piggy back it with something like this
http://www.ebay.com.au/itm/9999Hz-LED-D ... 3132wt_905
Edit: To make the circuit adjustable, replace the resistor across pins 6/7 of the 555 timer. Also, check that the timing cap and resistances result in the frequency range you want.
I've will post really simple/low cost calibration sources in the tach thread.
- paulpauly7
- CB900F
- Posts: 1945
- Joined: Tue Feb 21, 2012 6:57 pm
- Location: nz
Re: NQ50 build , nothing to lose , heaps to gain
this bike is now sold to NZHONDA for a great price of $300 Wow what a great deal ayden it will look even better with a paint job and a stroker motor
86 Nifty Fifty (spree)
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
Re: NQ50 build , nothing to lose , heaps to gain
Yes I bought this beast. I will start a new thread detailing my adventures. I am looking to totally rebuild this bike and ride it 2200km around the south island at the end of august.
Basic plan is 125cc AF18e Stroker, Dio Alloys and metallic silver body.
Basic plan is 125cc AF18e Stroker, Dio Alloys and metallic silver body.
Honda AF28 Dio ZX - Malossi 72cc
Honda DJ1R project
Honda DJ1R project
- paulpauly7
- CB900F
- Posts: 1945
- Joined: Tue Feb 21, 2012 6:57 pm
- Location: nz
Re: NQ50 build , nothing to lose , heaps to gain
i hope my corsa+scorpion setup in my nifty fifty can hold your stroker would be nice to take you but only time will tell
86 Nifty Fifty (spree)
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
ZX disk brake
Kitico 120kmh speedo
AF18 ZX ported
Polini corsa
Malossi crank
CTmani
24mmOKO
40pilot118main
Scorpion pipe
8.44 to 1
Michelin s1
71.3mph
92 yz125, 94 crm250
Re: NQ50 build , nothing to lose , heaps to gain
This thing is long gone, guess life gets in the way sometimes, but an ends a means to a new beginning, this below has had my wallet thin but my face happy
Was completely granny spec with popped engine when I got it.
but accidents happen
Could this be a new yarn to spin....
Will look into starting a new thread
Was completely granny spec with popped engine when I got it.
but accidents happen
Could this be a new yarn to spin....
Will look into starting a new thread
- Aaronshotme
- BMX
- Posts: 22
- Joined: Wed Nov 27, 2013 12:35 am
- Location: Austin
Re: NQ50 build , nothing to lose , heaps to gain
I love this! your car is really awesome too.