finally done a spreedio

monkeywrench · Post by **monkeywrench** » Fri Apr 29, 2011 8:04 pm

well i had the spree for a few months with a bad engine( hole in the case) so i decided to build a dio spree since i have 5 dio motors laying around. bad thing was is i didnt have a good crank for all the dio cases i have. i finally got a good crank and also bought bearings, seals and so on and so on.

everything on the af16e motor is stock besides a high variator,80jet and the home made air filter. the spree reaches speeds of about 40 as the speedo goes to the very end of the white line past the 35 mark.

Wheelman-111 · Post by **Wheelman-111** » Fri Apr 29, 2011 9:52 pm

Greetings:

Nice work MW. Turned the unpretentious Spree into a vehicle that'll hold its own in city traffic.
The engine hanger looks good!

monkeywrench · Post by **monkeywrench** » Fri Apr 29, 2011 10:40 pm

Wheelman-111 wrote:Greetings:

Nice work MW. Turned the unpretentious Spree into a vehicle that'll hold its own in city traffic.
The engine hanger looks good!

thanks! i used the elite hanger but cut the clutch cover side off a bit to fit down in the spree frame while centering the back wheel perfectly with the frame its pretty much a no brainer. the wiring was simple for the stator. i just cut off the connector from the spree stator and used the colors of the wires to the elite stator. the wire colors for both the spree and elite r the same. the bystarter is from the elite so i just cut the wires and reversed them so it would be yellow and green. im using the elite rectifier because the rectifier from the spree kept blowing tail lights and head light. i now have a modified head lamp for halogen bulbs. easy change in and out.

xxjareebxx · Post by **xxjareebxx** » Sat Apr 30, 2011 12:33 am

Looks real nice, would you sell one of your dios with a bad crank?

monkeywrench · Post by **monkeywrench** » Sat Apr 30, 2011 1:08 am

xxjareebxx wrote:Looks real nice, would you sell one of your dios with a bad crank?

i could sell one. they are just cases though ive taken the cranks out of them. i also have the intakes reed blocks and carbs for them but they r all seperated from the cases. also have the stators for them. basically have everything except cylinders pistons and cranks.

Trafficjamz · Post by **Trafficjamz** » Sat Apr 30, 2011 1:18 am

How much for a case?

xxjareebxx · Post by **xxjareebxx** » Sat Apr 30, 2011 1:48 am

monkeywrench wrote:
xxjareebxx wrote:Looks real nice, would you sell one of your dios with a bad crank?
i could sell one. they are just cases though ive taken the cranks out of them. i also have the intakes reed blocks and carbs for them but they r all seperated from the cases. also have the stators for them. basically have everything except cylinders pistons and cranks.

How much for everything but the top end and crank with he shrouds?

monkeywrench · Post by **monkeywrench** » Sat Apr 30, 2011 1:49 am

Trafficjamz wrote:How much for a case?

id say 50.00 plus shipping

monkeywrench · Post by **monkeywrench** » Sat Apr 30, 2011 1:52 am

xxjareebxx wrote:
monkeywrench wrote:
xxjareebxx wrote:Looks real nice, would you sell one of your dios with a bad crank?
i could sell one. they are just cases though ive taken the cranks out of them. i also have the intakes reed blocks and carbs for them but they r all seperated from the cases. also have the stators for them. basically have everything except cylinders pistons and cranks.
How much for everything but the top end and crank with he shrouds?

the shrouds i have r crap! but for the stator carbs intake and cases. id say 80.00 plus shipping.

monkeywrench · Post by **monkeywrench** » Sat Apr 30, 2011 1:56 am

xxjareebxx wrote:
monkeywrench wrote:
xxjareebxx wrote:Looks real nice, would you sell one of your dios with a bad crank?
i could sell one. they are just cases though ive taken the cranks out of them. i also have the intakes reed blocks and carbs for them but they r all seperated from the cases. also have the stators for them. basically have everything except cylinders pistons and cranks.
How much for everything but the top end and crank with he shrouds?

ill line up everything i have tommarow and take picks

xxjareebxx · Post by **xxjareebxx** » Sat Apr 30, 2011 2:11 am

Alright ill take it but could you wait till like Wednesday still have some scoots that could be a dio

monkeywrench · Post by **monkeywrench** » Sat Apr 30, 2011 2:32 am

xxjareebxx wrote:Alright ill take it but could you wait till like Wednesday still have some scoots that could be a dio

ok! i didnt plan on selling so i can wait tell wednesday. dont really need the money but i need to get rid of some stuff.

xxjareebxx · Post by **xxjareebxx** » Sat Apr 30, 2011 12:50 pm

monkeywrench wrote:
xxjareebxx wrote:Alright ill take it but could you wait till like Wednesday still have some scoots that could be a dio
ok! i didnt plan on selling so i can wait tell wednesday. dont really need the money but i need to get rid of some stuff.

Alright sweet

fastplastic · Post by **fastplastic** » Sun May 01, 2011 1:30 am

Take some pics of how kick stand it mounted

monkeywrench · Post by **monkeywrench** » Sun May 01, 2011 8:03 pm

fastplastic wrote:Take some pics of how kick stand it mounted

i will do this tommarow as it is pouring rain right now

Honda Spree and Elite 50 Forums

finally done a spreedio

finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio

Re: finally done a spreedio